541948
5
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
Batteries installation
1. Open battery compartment on the back of the unit by removing the two small
screws (RTS 2) with a Philips head screwdriver. (see figure 4)
2. Install / replace with 2x “AAA size batteries in the compartment. It is
recommended that only alkaline batteries are used. Do not use rechargeable
batteries.
3. The weather station is capable of receiving up to 3 different channels. Select
the channel number (1, 2, or 3) by sliding the “Channel 1 2 3” switch (RTS 4).
If you only have 1 remote temperature sensor, select 1.
4. Press the “reset” button (RTS 3) once and the red light will flash once.
5. Replace the battery compartment on the back of the unit by tightening the
two screws (RTS 2).
Installation
1. Place the remote temperature sensor at a desired place by mounting the
units hang hole (RTS 1) on a screw (screw not included). Alternatively, the
unit can be place on a flat horizontal surface.
2. The unit can be placed indoor or outdoor. The unit is weather proof. Do not
submerge unit in water. Do not expose unit to water for prolonged periods.
Avoid accumulation of water and or snow on unit. Avoid exposing unit to
direct sunlight. Remove unit from the exterior in extreme or harsh weather,
including but not limited to hurricane, typhoon, and cyclones seasons. Do not
place the unit in area of high winds.
3. Do not place the remote temperature sensor more than 30 meters (98 feet)
from the receiving weather station. The remote temperature sensor is most
effective if there are no obstruction and interference between the remote
temperature sensor and the weather station. The remote temperature sensor
might have to closer than 30 meters if the weather station is not able to
receive any signals. This is due to obstructions and interference. The user
might need to experiment with various locations to get the best reception.
Configuring Weather Station to receive remote temperature signals.
1. Follow the above instructions to set up remote temperature sensor.
2. Press “CHANNELbutton (6) on weather station for 3 seconds. will flash.
This will reset all temperature memories.
3. The weather station will begin scanning for signals for channel 1. As soon as
signals are received for channel 1, the temperature will be displayed. The
weather station will automatically scans for the other channels. It will scan
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Techno line WT643 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Techno line WT643 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Techno line WT643

Techno line WT643 Gebruiksaanwijzing - Deutsch - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info