517190
27
Verklein
Vergroot
Pagina terug
1/31
Pagina verder
27
11. INSPECTION AND MAINTENANCE BEFORE RIDING
CHECKING AND CHANGING FUSES
Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having
the same specified amperage rating (7A). Using a fuse of more than 7 amperes, a brass or iron wire to
replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.
y Remove the battery cover screws, and open the battery cover. Fuses are installed in the fuse box
located by the battery.
y Fuses must be firmly secured with wire connectors when replacing.
y Use only parts having the specified specification to replace electrical components such as light bulbs.
Using parts not having the specified specifications for replacement may cause the fuse to blow and
over-discharge the battery.
y Avoid spraying water directly on or around fuse box when washing the motorcycle.
y Take your scooter to your dealer for an inspection if a fuse is blown by unknown causes.
REMOVE】【INSTALLATION
CHECKING THE TURN SIGNAL LIGHTS AND HORN
y Turn the ignition switch key to “ON” position.
y Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights
flashes and also check if the warning buzzer sounds.
y Check turn signal light covers if they are dirty, crack, or loosen.
y Press horn button to check if it works.
CHECKING THE FRONT AND REAR LIGHTS
y Turn the ignition switch key to “ON” position, start the engine and then turn on the front light switch.
Check if front and rear lights come on.
y Check the brightness and direction of front light by projecting the light on the wall to see if it is correct.
y Check the front light cover if it is dirty, crack, or loosen.
CHECKING THE BRAKE LIGHT
y Turn the ignition switch key to “ON” position, hold the hand-braking levers for front and rear wheels.
Check if the brake lights come on.
y Check the brake light cover if it is dirty, crack, or loosen.
Wire
Fuse connectors
Fuse
Press in from above
CAUTION:
y Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation
of turn signal lights will be affected.
y Switch on the turn signal before changing lanes or marking a turn to inform others of your intent.
y After changing lanes or making a turn, switch of turn signal immediately by pressing the reset
button. This button is located in the center of the turn signal switch.
CAUTION:
y Use only SANYANG specified bulbs, do not use bulbs with different specifications to avoid
damaging electrical system, burning out bulbs, and discharging the battery.
y Do not modify or add other electrical components to your scooter. This may prevent an over load
or short circuit which may result in a fire some cases.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sym JET EUROX 50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sym JET EUROX 50 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info