3. Installation
For the version fitted with a towel rail, BEFORE MOUNTING THE FAN HEATER ON THE WALL:
- fit the towel rail into the holes underneath the product, figure 2
- insert and tighten the 4 (short) screws contained in the bag, figure 3
- The mimimum distance from the floor reported in figure 4 (30cm) changes to 60cm.
Mount the heater on the wall making sure to observe the minimum distances from the ceiling, floor
and other walls, as shown in figure 4
Drill three 6 mm diameter holes in the wall, as shown in figure 5
Insert the three wall plugs supplied with the product
Insert the 2 upper screws, contained in the same bag, taking care to leave a distance of 8 mm
between the head of the screws and the wall
Gripping the heater firmly, hook it onto the two screws; CAUTION! Before releasing the heater
make sure it is attached to the 2 screws.
Then secure the product with the lower screw, figure 6
4. Using the fan heater
The heater is fitted with the controls shown in figure 7
Model with thermostat
Starting from the anti-freeze position “✽”, turn the thermostat knob clockwise until you hear a
“click”: the fan heater starts working at 1800w and the indicator LED lights up.
The thermostat maintains the required ambient temperature by automatically turning the heater on
and off. The more the knob is turned clockwise to a higher number, the higher the ambient
temperature will be. The highest position of the thermostat corresponds to approximately 35°C, the
bottom one (*) to about 5°C.
Using the thermostat
In a room with a temperature in excess of 35°C, the thermostat does not turn on the fan heater
even if it is at maximum.
Vice-versa, in a room with a very low temperature (below 5°C), the thermostat keeps the heater
constantly on, even if it is at minimum.
To optimise use of the thermostat, proceed as follows:
- turn the thermostat knob to maximum and wait until a comfortable temperature is reached;
- then turn the thermostat knob anti-clockwise until you hear a “ click” and the heater turns off;
- turn the thermostat knob clockwise just a little;
- in this position, the thermostat will maintain the selected ambient temperature.
Model with thermostat and 60’ timer
This model of fan heater is fitted with two knobs, one for the 60’ timer and the other for the
thermostat.
2 different operating modes are available:
A Maintenance of ambient temperature:
Starting from the anti-freeze position “✽”, turn the thermostat knob clockwise until you hear a
“click”: the fan heater starts working at 1000w and the indicator LED lights up.
The thermostat maintains the required ambient temperature by automatically turning the
heater on and off. The more the knob is turned clockwise to a higher number, the higher the
ambient temperature will be. The highest position of the thermostat corresponds to
approximately 35°C, the bottom one (*) to about 5°C .
To adjust the thermostat, see the USING THE THERMOSTAT section above.
B Rapid heating
Adjust the ambient thermostat to the required temperature and then turn the timer knob to
select the required operating time. The product rapidly heats the room 1800w for the set time
and then reduces power to 1000w to maintain the ambient temperature selected with the
thermostat.
When the heater is working under timer control at 1800w the thermostat doesn't control the room
temperature. In this condition, do not use the heater in small rooms when they are occupied by
persons not capable of leaving the room on their own, unless constant supervision is provided by a
person responsible for their safety.
5. Filter
This product is fitted with a filter to protect the heating elements from dust and dirt.
The filter is removable and can be fitted both from the left and from the right, figure 8.
To keep the heater in perfect condition, clean the filter once every six months REMEMBERING TO
PUT IT BACK AGAIN AFTERW ARDS.
6. Towel rail
The towel rail can warm up to 2 towels at a time.
Position the towels correctly on the rail, as shown in figure 9 and NOT as shown in figure 10, to
prevent overheating and malfunctions.
7.. What to do in case of malfunctions
In the event of overheating, the safety device on the appliance automatically disabled the heating
elements and motor. As a result, the heater stops working, even though the indicator LED stays
on.
In this case:
-
Turn off the fan heater and allow it to cool down for about 15/20 minutes.
-
Make sure the dust filter is not totally obstructed and clean if necessary. Remember to put it back
again afterwards.
-
Eliminate any other possible reasons for overheating (e.g.: obstructions in front of the air inlet/outlet
grilles, build-ups of dirt).
-
Turn on the fan heater again and check it works correctly.
-
If the product needs servicing, call in a qualified specialised technician.
