720427
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7
ENGLISH
Notes:
a. Never change the position of the forward/reverse switch
(4) while the screwdriver bit is turning.
b. The variable speed trigger switch (5) will NOT function
with the forward/reverse switch (4) in the middle
position.
Variable speed trigger switch (Fig. C)
This screwdriver is equipped with a variable speed On/Off
trigger switch.
1. To start screwdriver, gently squeeze the variable speed
trigger switch (5).
Note: The screwdriver will turn at its slowest speed when
the variable speed trigger switch is depressed slightly. The
screwdriver will turn at its fastest speed when the variable
speed trigger switch is fully depressed.
2. To stop the screwdriver, release the variable speed
trigger switch (5).
Lock-on button (Fig. D)
The lock-on button feature allows the trigger switch to be
locked in the ON position at full speed when continuous
operation for extended periods of time is required.
To lock the lock-on button in the ON position, pull back on
the variable speed trigger switch (5) to start the screwdriver
and push the lock-on button (6) into the screwdriver handle.
Release the variable speed trigger switch while holding the
lock-on button into the screwdriver handle. The screwdriver
will continue to run. To release the lock-on button, pull
variable speed trigger switch back (5) and then release the
trigger.
Note: Operating the screwdriver with the variable speed
trigger switch for an extended period of time may cause the
screwdriver motor to overheat. If the screwdriver gets hot,
stop driving screws and allow it to cool for at least 15
minutes.
Inserting a screwdriver bit (Fig. E)
This tool has a magnetic bit holder that provides convenient
bit changes. To install a bit, simply insert the hex bit shank
(7) into the magnetic bit holder (8) that is located inside the
depth stop (1). Push the bit into the magnetic bit holder until
the magnet holds the bit in place.
Notes:
a. Use only 1” (25 mm) long bits that are designed for use
in driving drywall screws.
b. Make sure the bit size is correct for the drywall screws
being driven. This will usually be a #2 size.
Replacing the magnetic bit holder (Fig. F)
If the magnetic bit holder becomes worn or damaged, it must
be replaced. The replacement bit holder must be of the
same dimensions as the original and have the ANSI
retention groove on the end that is inserted into the tool.
1. Remove the nosepiece (2) by turning it counter
clockwise.
Note: Do not use pliers on the nosepiece. Only use your
hand.
2. Grasp the screwdriver bit (7) with pliers and pull it out of
the magnetic bit holder (8).
3. Grasp the large end of the bit holder with pliers and pull
it straight out of the screwdriver spindle (9).
4. Reverse the process by inserting the replacement
magnetic bit holder into the tool.
Note: When inserting the replacement for magnetic bit
holder, gently tap it into place to make sure it is fully inserted.
Grasp the large end of the magnetic bit holder to ensure the
retention groove (10) is holding the magnetic bit holder in
place in the tool.
5. Reinstall the screwdriver bit and nose piece.
Safety Recommendations
Check the following every time you use the screwdriver:
1. Wear safety glasses or a mask.
2. Use hearing protection.
3. The screwdriver tip is the right size and it is in good
condition.
4. No power cables “live” where you are inserting the
screws.
Note: Failure to follow these safety rules will significantly
increase the risk of injury.
(Original instructions)
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STDR5206 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STDR5206 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info