720787
5
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
(Original instructions) ENGLISH
5
for any reason, switch off the power tool and hold the
cutting unit motionless until the wheel comes to a
complete stop. Never attempt to remove the wheel
from the cut while the wheel is in motion otherwise
kickback may occur. Investigate and take corrective
action to eliminate the cause of wheel binding.
f) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
g) Support any oversized workpiece to minimize the risk
of wheel pinching and kickback. Large workpieces tend
to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
CHOPSAW SAFETY WARNINGS
Always wear proper eye and respiratory protection.
Before using, inspect the cutting wheel for cracks or
flaws. If such a crack or flaw is evident, discard the
wheel. The wheel should also be inspected whenever
you think the tool may have been dropped. Flaws may
cause wheel breakage.
When starting the tool with a new or replacement
wheel or if you are unsure of the condition of the
wheel, hold the tool in a well protected area and let it
run for one minute. If the wheel has an undetected crack
or flaw, it should burst in less than one minute. Never start
the tool with a person in line with the wheel. This includes
the operator.
In operation, avoid bouncing the wheel or giving it
rough treatment. If this occurs, stop the tool andinspect
the wheel for cracks or flaws.
Clean your chop saw periodically following the
procedure in this manual.
Do not remove wheel guards or base.
ALWAYS used on a stable and level surface.
ALWAYS wear gloves when handling wheels.
ALWAYS USE THE VISE OR SPECIAL FIXTURE TO
CLAMP WORK SECURELY. Other aids such as spring,
bar, or C-clamps may be appropriate for certain sizes and
shapes of workpiece. Use care in selecting and placing
these clamps and make a dry run before making a cut.
Use only 14” type 1 wheels rated at 4100 rpm or higher.
Allow cut off parts to cool before handling.
Do not attempt to cut wood or plastic with this tool.
NEVER CUT MAGNESIUM WITH THIS TOOL.
In case of workpiece fragments jammed between saw
blade and guards, disconnect the machine from the power
supply. Remove the jammed parts and reassembling the
saw blade.
Use chop saw in a well-ventilated area.
Turn chop saw off before removing any pieces from the
base.
DO NOT CUT ELECTRICALLY LIVE MATERIAL.
Do not use circular saw blades or any other toothed
blades with this tool. Serious injury may result.
DO NOT OPERATE THIS TOOL NEAR FLAMMABLE
LIQUIDS, GASES OR DUST. Sparks or hot chips from
cutting or arcing motor brushes may ignite combustible
materials.
Do not use the side of the abrasive wheel as a deburring
grinder. This will substantially weaken the wheel creating
an unsafe condition. The wheel may come apart.
CAUTION: Wear appropriate hearing protection`
during use. Under some conditions and duration ofuse,
noise from this product may contribute to hearing loss.
CAUTION: Spark deflector will get hot. Avoid touching
or adjusting while hot. Keep cordset and materials away
from spark deflector.
Avoid prolonged contact with dust from sawing and
other construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful
chemicals.
WARNING: Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure.
Direct particles away from face and body.For your
convenience and safety, the following warnings are on
your Heavy-Duty 14” (355mm) Chop Saw:
DO NOT USE TOOTHED BLADES.
USE ONLY REINFORCED WHEELS RATED 4100 RPM
OR HIGHER.
WHEN SERVICING USE ONLY IDENTICAL
REPLACEMENT PARTS.
ALWAYS: WEAR EYE PROTECTION, USE GUARDS,
CLAMP WORK IN VISE, USE PROPER RESPIRATORY
PROTECTION.
ALWAYS STORE CUTTING DISCS WELL- PROTECTED
AND IN A DRY PLACE, OUT OF REACH OF CHILDREN
ONLY USE CHOP SAW WHEEL OF A MAX.
THICKNESS OF 3.0 MM AND A MAX. DIAMETER OF
355mm.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
- Impairment of hearing
- Risk of personal injury due flying particles.
- Risk of burns due to accessories becoming hot during
operation.
- Risk of personal injury due to prolonged use.
- Risk of dust from hazardous substances.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SSC22 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SSC22 in de taal/talen: Engels, Frans, Turks als bijlage per email.

De handleiding is 2,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info