622599
7
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
7
ENGLISH
(Original instructions)
u Replace the cutting disc (J). Make sure that the new disc
is placed onto the spacer (R) in the correct rotational
direction.
u Secure the blade with the retaining ange (U), the washer
(T) and the bolt (S).
u Push in the spindle lock (L).
u Rotate the cutting disc (J) until it locks.
u Using the at wrench (G), tighten the bolt (S) by turning
clockwise.
u Move the guard back down and release the spindle lock
(L).
u Adjust the cutting depth as necessary.
Adjusting the cutting depth (g. 1)
The cutting depth can be adjusted to meet the wear of the
cutting disc.
u Make a dry run with the tool switched off and check for
clearance.
u If adjustment is required, proceed as follows:
u Loosen the lock nut (M) a few turns.
u Turn the depth stop bolt (M) in or out as to achieve the
required cutting depth.
u Tighten the lock nut (M).
Warning: Always adjust the depth stop to its original position
when replacing the cutting disc.
Clamping the workpiece in position (g. 2 - g 4)
The tool is equipped with a vise (F)
u Pull the lever (I) toward the handle (H).
u Push the vise (F) forward until the jaw is almost touching
the workpiece.
u Press the lever (I) toward the jaw until it engages with the
clamp shaft.
u Rotate the handle (H) clockwise and clamp the workpiece
securely.
u To release the workpiece, rotate the handle (H)
counterclockwise.
u To increase the cutting capacity, place a spacer block
under the workpiece. The spacer block should be slightly
narrower than the workpiece.
Warning: Support long workpieces using a piece of wood. Do
not clamp the cut off end.
Quick travel feature (g. 4)
The clamp has a quick travel feature.
u To release the clamp, rotate the handle (H) one or two
turns counterclockwise and pull the lever (I) toward the
handle (H).
Setting the clamping position (g. 5)
The clamping position can be set to match the cutting disc.
u Remove the fence bolts (P) using the at wrench (G).
u Move the fence (E) as required.
u Re-t the fence bolts (P) and tighten them to lock the
fence (E).
Adjusting the angle of cut (g. 6)
The tool can be used for mitre cuts up to 45°.
u Loosen the fence bolts (P) to release the fence (E).
u Set the fence (E) to the required angle. The angle can be
read on the scale (Q).
u Tighten the fence bolts (P) to lock the fence (E).
Checking and adjusting the mitre scale (g. 6)
u Loosen the fence bolts (P) to release the fence (E).
u Pull down the arm and lock it in this position by attaching
the lock chain (A).
u Place a square against the fence (E) and the left side of
the cutting disc creating a perfect 90°. Check that the 0°
marking on the scale (Q) aligns with the marking on the
base (D).
u Tighten the fence bolts (P) to lock the fence (E).
u Remove the lock chain (A) and return the arm to its upper
rest position.
Adjusting the spark deector (g. 1)
u Loosen the screw (B).
u Set the spark deector (C) as appropriate.
u Tighten the screw (B).
Use
Warning: Always observe the safety instructions and
applicable regulations.
Warning: Do not apply excessive pressure to the tool.
Warning: Avoid overloading. Should the tool become hot, let
it run a few minutes under no load condition.
Cutting capacity
The wide vise opening and high pivot point provide cutting
capacity for many large pieces. Use the cutting
capacity chart to determine total maximum size of cuts that
can be made with a new wheel.
Caution: Certain large, circular or irregularly shaped objects
may require additional holding means if they cannot be held
securely in vise.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FME700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FME700 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 4,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info