622607
7
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
7
ENGLISH
(Original instructions)
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
ash at each speed and repeat.
Selecting the direction of rotation (g. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(2) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
u To lock the tool, set the forward/reverse slider into the
centre position.
Selecting the torque (g. E)
This tool is tted with a collar to set the torque for various
screwdriving and drilling applications. Large screws and hard
workpiece materials require a higher torque setting than small
screws and soft workpiece materials. For the denition of the
symbol refer to the listing below.
u For drilling in wood, metal and plastics, set the torque
adjustment collar (4) to the
b
symbol.
u For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
- Set the torque adjustment collar (4) to the lowest torque
setting.
- Tighten the rst screw.
- If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Speed selector (g. D)
u For drilling in steel and for screwdriving applications, slide
the speed selector (8) towards the rear of the tool (1st
gear).
u For drilling in materials other than steel, slide the speed
selector (8) towards the front of the tool (2nd gear).
Drilling/screwdriving
u Select forward or reverse rotation using the forward/re-
verse slider (2).
u To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
u To switch the tool off, release the switch.
LED work light
The LED work light (7) is activated automatically when the trig-
ger is depressed. The LED work light will illuminate when the
trigger is partially depressed, before the unit begins running.
Hints for optimum use
Drilling
u Always apply a light pressure in a straight line with the drill
bit.
u Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
u Use a block of wood to back up workpieces that may
splinter.
u Use spade bits when drilling large diameter holes in wood.
u Use HSS drill bits when drilling in metal.
u Use masonry bits when drilling in soft masonry.
u Use a lubricant when drilling metals other than cast iron
and brass.
u Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
u Always use the correct type and size of screwdriver bit.
u If screws are difcult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your Stanley Fat Max tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your Stanley Fat Max product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Stanley-FMC010

Zoeken resetten

  • Waar vind ik een servicecentrum waar ik nieuwe accu' s kan kopen en laten reviseren voor een Stanley
    boormachine nr FMC010LB?













    Gesteld op 21-6-2020 om 21:21

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FMC010 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FMC010 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info