603490

Standard Horizon RAM 3 - CMP30 Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
RAM3
(
CMP30
)
CONTROLS
[
H/L
]
Key
Press this key to toggle the transmit power between high
and low. When the
[
H/L
]
key is pressed while the trans-
ceiver is on channel 13 or 67, the power will temporarily
switch from LOW to HI power until the PTT is released.
The
[
H/L
]
key does not function on transmit inhibited and
low power only channels.
PTT
(
Push-To-Talk
)
Key
Press this key to activate the transmission.
POWER
(
)
Key
Press and hold down this key to turn to the transceiver
and RAM3
(
CMP30
)
“on” and “off”.
Microphone
The internal microphone is located here.
When transmitting, position your mouth about 1/2 to 1 inch
(1.2 ~ 2.5 cm) away from the small mic hole. Speak slowly
and clearly into the microphone.
DISPLAY
Channel display.
SOFT KEY
For details, refer to “Mode Setting and Setup” above.
KEY PAD
[
CALL/MENU
]
Key
Press this key to access the DSC OPERATION menu.
Press and hold this key to access the SETUP menu.
[
16/9
]
Key
First press: channel 16 is immediately selected.
Second press: recalls the last selected channel.
Press and hold: selects channel 9.
[
S
](
UP
)
/
[
T
](
DOWN
)
Key
These keys are used to select channels, adjust the vol-
ume and squelch level, and to choose DSC calls, DSC
setup and Radio setup function.
[
VOL/SQ
]
Key
(
Volume Control / Squelch Control
)
Press this key to toggle the function of the microphone’s
[
S
]
or
[
T
]
key between the channel selections, volume
level adjustment, and squelch level adjustment.
[
CLR/WX
]
Key
For details, refer to “Mode Setting and Setup” above.
[
ENT
]
Key
This key functions as the enter key.
Speaker
The internal speaker is located here.
[
DISTRESS
]
KEY
This key is used to send a DSC Distress Call.
Lift the red spring loaded DISTRESS cover, then press
and hold in the
[
DISTRESS
]
key.
MODE SETTING & SETUP
The RAM3
(
CMP30
)
is backward compatible Standard Horizon VHF radios that use the RAM+
(
CMP25
)
and VH-310
(
telephone style handset
)
.
MODE SELECTION
The Mode selection allows the RAM3
(
CMP30
)
to be setup to
operate with specific models, refer to the section below for
compatibility.
Mode 1: GX1256S, GX1280S, and GX2360S
Mode 2: PS1000, PS2000, CPV350, CPV550, GX1500S/E,
GX3000S/E, GX3500S
Ú
, GX5000S, GX5500S,
and VM-3500E
Ú
Ú To use Mode 2 on the GX3500S or VM-3500E the radio
software may have to be updated. Please contact Stan-
dard Horizon for details.
1. Turn the RAM3
(
CMP30
)
off, press
and hold the
[
ENT
]
key then press
and hold the orange POWER
(
)
key until the menu is shown.
2. Press the
[
S
]
or
[
T
]
key to select
“
Operation ModeOperation Mode
Operation ModeOperation Mode
Operation Mode” item, then press
the
[
ENT
]
key.
3. Press the
[
S
]
or
[
T
]
key to select the Operation Mode
(“
Mode 1Mode 1
Mode 1Mode 1
Mode 1” or “
Mode 2Mode 2
Mode 2Mode 2
Mode 2”) and press the
[
ENT
]
key.
4. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
KEY SETUP
The following are used only when Mode 2 is selected
and the RAM3
(
CMP30
)
is connected to a compatible
radio.
[
CLR/WX
]
Function:
The operation of this key may be changed to select WX chan-
nels for North American market or CLR for Europe. By default
the when the key is pressed, the last selected WX channel
will be shown.
1. To change this key to operate the
CLR function, Turn the RAM3
(
CMP30
)
off, press and hold the
[
ENT
]
key then press and hold the
orange POWER
(
)
key until the
menu is shown.
2. Press the
[
T
]
key to select “
[
CLRCLR
CLRCLR
CLR/
WXWX
WXWX
WX
]
Function Function
Function Function
Function” and press the
[
ENT
]
key.
3. Select “
CLRCLR
CLRCLR
CLR” and press the
[
ENT
]
key.
4. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
Define
[
Soft
]
Keys:
By default the soft keys are assigned as SCAN, DW and NAV,
however these keys can be changed. In addition the soft keys
can be increased / assigned, refer below:
1. Turn the RAM3
(
CMP30
)
off, press
and hold the
[
ENT
]
key then press
and hold the orange POWER
(
)
key until the menu is shown.
2. Press the
[
T
]
key to select “
DefineDefine
DefineDefine
Define
[
SoftSoft
SoftSoft
Soft
]
keys keys
keys keys
keys” and press the
[
ENT
]
key.
3. Press the
[
S
]
or
[
T
]
key to select
the
[
Soft
]
key, and press the
[
ENT
]
key. Then, press the
[
S
]
or
[
T
]
key
to select the new function to be
assigned, and press the
[
ENT
]
key.
Available functions are listed below.
4. Press the
[
CLR/WX
]
key to return
to the “Soft Key Setup” mode.
5. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
Number of Soft Keys:
3 soft keys are set as default. However the RAM3
(
CMP30
)
allows assigning of up to 10 soft keys with the instructions
below:
1. Turn the RAM3
(
CMP30
)
off, press
and hold the
[
ENT
]
key then press
and hold the orange POWER
(
)
key until the menu is shown.
2. Press the
[
T
]
key to select “
Num-Num-
Num-Num-
Num-
ber of Soft keysber of Soft keys
ber of Soft keysber of Soft keys
ber of Soft keys” and press the
[
ENT
]
key.
3. Select the number of soft keys (3,
4, 6, 8 or 10) and press the
[
ENT
]
key.
4. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
IMPORTANT NOTE
Mode 2 only allows the RAM3
(
CMP30
)
to define the
[
CLR/WX
]
key and assign / Change the number of se-
lectable soft keys.
DISPLAY
SCAN
DW
NAV
DIM
MEM
IC
PA
FOG
SCRM
WX
CLR
FUNCTION
Ú
Stops and starts scanning.
Stops and starts Dual Watch Scan.
Displays the GPS Navigation Data.
Enables the LCD backlight dimmer function.
When pressed memorizes a channel for scanning.
Activates the Intercom function.
Operates the PA function.
Operates the Fog Horn function.
Toggles the Voice Scrambler “on” and “off”.
Immediately recalls the previously selected US
NOAA weather channel.
Cancels the menu selection.
Ú: Some functions may not operate depending on the connected radio.
OPTIONAL ACCESSORIES
CT-100 23FT EXTENSION CABLE
MLS-310 10 WATT AMPLIFIED SPEAKER
MLS-300 EXTERNAL LOUD SPEAKER
LCD SETTING
The RAM3
(
CMP30
)
has the capability to change the LCD
contrast by following the instructions below.
1. Press and hold down the
[
CALL/MENU
]
key until “
RADIORADIO
RADIORADIO
RADIO
SETUPSETUP
SETUPSETUP
SETUP” menu appears.
2. Press the
[
CALL/MENU
]
key, then
press the
[
T
]
key until the “
CON-CON-
CON-CON-
CON-
TRASTTRAST
TRASTTRAST
TRAST” menu appears.
3. Press the
[
CALL/MENU
]
key again,
then press the
[
S
]
or
[
T
]
key to se-
lect the desired contrast level.
4. Press the
[
CALL/MENU
]
key to
store the selected level, then press
the
[
16/9
]
key to exit “
RADIO SETUPRADIO SETUP
RADIO SETUPRADIO SETUP
RADIO SETUP”
menu and return to radio operation
mode.
SPECIFICATIONS
Supply voltage: 13.8 VDC (Supplied from the transceiver)
Current consumption: 700 mA @VOL Max.
200 mA @AF Mute
Operating Temperature: –4 °F to +140 °F (–20 °C to +60 °C)
MIC. Sensitivity (Typical): 60 mVrms
@ 1 kHz Tone with 3 kHz Deviation
MIC. Impedance:2 kΩ
AF output: 300 mW @ 16 Ω for 10 % THD
(Internal Speaker)
2 W @ 4 Ω for 10 % THD
(External Speaker)
Display Size: 1.8” x 0.9” (45 x 23 mm)
Display Resolution: 132 x 64 dot
Case Size: 2.6” x 5.5” x 1.2” (67 x 140 x 30 mm)
Weight (Approx): 11.6 oz (330g)
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Standard Horizon RAM 3 - CMP30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Standard Horizon RAM 3 - CMP30 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info