603502
28
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
Page 30
surface to the bottom). Try decreasing the STC value to SHORT in shallow waters or to
switch it to VERY SHORT or OFF.
Auto Range fails, and the digital depth readout displays a very shallow
reading. What should I do?
This usually happens if the STC is off or is set to a low value causing disturbance from
Surface Clutter to be stronger than bottom echoes. Try increasing the STC value. As
general rule STC has to be set as in shallow waters and LONG in depth waters.
Auto Range fails in very deep waters displaying a digital very shallow depth
readout. What should I do?
The Fish Finder capability to detect the bottom decreases as the bottom depth increase. If
the bottom composition is soft as mud, if the sea conditions are bad, if there are thermoclines
or the water is full of materials in suspension it can further decrease thus causing the digital
depth readout to fail. When this happens the Auto Range algorithm also fails. To recover
from this situation it is necessary to switch to Manual Range mode and to set the Manual
Depth mode. When Manual Depth mode is selected the algorithm that calculates the digital
depth readout searches for the bottom within the range manually selected by the user. At
this point it is necessary to increase manually the Range until the bottom becomes
graphically visible. If the echoes from the bottom are strong enough, the Fish Finder shall
look to the bottom giving a correct depth reading and shall be possible to return in Auto
Range mode. Please note that if one or more of the conditions that reduce the echoes from
the bottom listed above is true the bottom may be not visible at all, in this situation a strong
thermocline or Surface Clutter may be interpreted by the Fish Finder as the bottom.
At a very shallow range upper half of the screen appears almost completely
filled by the Surface Clutter. How can I eliminate it?
This is normal in shallow waters. To clean up the Surface Clutter without degrading the
digital depth readout algorithm functionality there are two modes:
1. If Surface Declutter = OFF it is possible to set the STC value to custom setting the STC
length to the same size of the Surface Clutter, and increasing the STC strength until the
image on the screen cleans up. Please note that in very shallow waters it is usually better
to switch to Manual Gain mode to reduce Gain fluctuation due to rapidly changing
bottom conditions.
2. Using Surface Declutter, increase the Surface Declutter value until the Surface
Declutter disappears completely.
Why do I never see fish in the range between 0 to 2 Ft?
The minimum range of the Fish Finder is 2 Ft. In this interval the Fish Finder can detect
neither the bottom nor any target.
How can I reduce the Surface Clutter?
You can act by: properly setting the STC and also by increasing the NOISE LEVEL and
reducing the GAIN or the GAIN OFFSET (if you are in Auto Gain mode). However please
note that a strong attenuation of Surface Clutter may also reduce the capability to detect
targets.
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Standard Horizon FF-525 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Standard Horizon FF-525 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Standard Horizon FF-525

Standard Horizon FF-525 Installatiehandleiding - English - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info