583956
18
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
30
Treadmill
XT485
31
Treadmill
XT485
1. Tether cord not in position.
2. Circuit breaker on front grill tripped.
Push circuit breaker in until it locks.
3. Plug is disconnected. Make sure plug is rmly pushed
into 115 VAC wall outlet.
4. Breaker panel circuit breaker may be tripped.
5. Treadmill defect. Contact your Spirit Fitness dealer.
Display does not light
Tread-belt does not stay centered
Treadmill belt hesitates when
walked/run on
The user may be walking while favoring or putting more
weight on either the left or right foot. If this
walking pattern is natural, track the belt slightly
off-center to the side opposite from the belt
movement. See General Maintenance section on
Tread-belt Tension. Adjust as necessary.
1. If the belt moves, but stops after a short time and
thedisplay shows “LS”, run calibration.
2. If you press start and the belt never moves, then the
display shows LS, contact service.
Motor is not responsive after press-
ing start
Treadmill will only achieve
approximately 7 mph but shows higher
speed on display
This indicates motor should be receiving power to
operate. Low AC voltage to treadmill. Do not use an
extension cord. If an extension cord is required it should
be as short as possible and heavy duty 16 gauge
minimum. Low voltage. Contact an electrician or your
Spirit Fitness dealer. A minimum of 110 volt AC current
is required.
High belt/deck friction. See General Maintenance
section on cleaning the deck. If cleaning doesn’t prevent
this from reoccurring, check to see if there is signicant
wear of the deck. If so, the deck may need to be ipped if
it is on its original side
Tread-belt stops quickly/suddenly when
tether cord is pulled
High belt/deck friction. See General Maintenance. If
cleaning doesn’t prevent this from reoccurring, check the
amp draw of the motor. If this is high and there are signs
of signicant wear of the deck, it may need to be ipped if
it is on its original side
Treadmill trips on board 15 amp circuit
Treadmill may not be grounded. Static electricity is
“crashing” the computer. Refer to Grounding
Instructions on page 3.
Computer shuts off when console is
touched (on a cold day) while
walking/running
Need to replace the breaker with a “High In-rush current”
type breaker (see page 3 for details)
Circuit breaker trips, but not the
treadmill circuit breaker
Service Checklist - Diagnosis Guide
Do not lubricate with other than Spirit Fitness approved lubricant.
Your treadmill comes with one tube of lubricant and extra tubes can
be ordered directly from Spirit Fitness or your authorized Spirit Fitness
dealer.
Keeping the deck lubricated at the recommended intervals ensures
the longest life possible for your treadmill. If the lubricant dries out, the
friction between the belt and deck rises and places undue stress on
the drive motor, drive belt and electronic motor control board, which
could result in catastrophic failure of these expensive components. Failure to lubricate the deck at regular
intervals may void the warranty.
The belt & deck come pre-lubricated and subsequent lubrication should be performed every 180 hours
of use. The console has a built in lubrication reminder indicator that lights every 180 hours of use.
Use the lubricant to lubricate the deck beneath the belt. If you can reach under the belt approximately
6” on each side, use the following procedure: Unplug the electrical cord. At the middle of the deck, lift up
on the belt and reach under with the tube of lubricant. Squirt most of the lubricant on the deck surface.
Repeat the process on the opposite side. Plug the electrical cord back into the outlet and walk on the belt
at a moderate speed for ve minutes.
If unable to perform the above procedure, it will be necessary to loosen the walking belt. Using the 6
mm Allen wrench supplied, loosen the two rear roller adjustment bolts -- located in the rear end caps –
enough to get your hand under the belt (5 –10 turns). Make sure to loosen both bolts the same amount
of turns and also remember how many turns, because when nished you will need to tighten the bolts
back to the point they were before.
Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the whole
tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out the contents
of the tube across the deck (parallel to the motor cover) in about a one-foot line, like toothpaste on a
toothbrush. The one-foot line should be in the middle of the deck at approximately equal distance from
both side edges of the belt. You want the lubricant to be applied about the spot that your feet would hit
the belt as you are walking. This should be about 18 inches from the motor cover, but you may want to
walk on the treadmill before loosening the belt to note where your feet land on the belt. If you mostly use
the treadmill for running, the spot where your feet land may be different from walking.
Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you
loosened them. Run the treadmill at about 3 mph without walking on it for about a minute or two to
make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the belt
tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on the treadmill
immediately for at least 5 minutes to ensure the lubricant is evenly distributed.
Belt/Deck Lubrication Procedure
Problem Solution/Cause
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Spirit XT485 2011-2012 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Spirit XT485 2011-2012 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info