583923
30
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
26
Treadmill
XT185
If the calibration does not pass you may need to check the speed sensor alignment.
1. Remove the motor cover hood by loosening the 8 screws that hold it
in place. Set it aside.
2. The speed sensor is located on the left side of the frame, right next to the
front roller pulley (the pulley will have a belt around it that also goes to the
motor). The speed sensor is a small rectangular shaped black box with a
wire connected to it.
3. You will see a magnet on the outside edge of the pulley; make sure the
speed sensor is aligned with the center of the magnet when it passes by.
There are two a screws that hold the sensor in place that need to be
loosened to adjust the sensor. Re-tighten the screws when nished.
The console has built in maintenance/diagnostic software. The software will allow you to change
the console settings from English to Metric and turn off the beeping of the speaker when a key
is pressed for example. To enter the Engineering Mode Menu press and hold down the Start,
Stop and Enter keys, then insert the safety key. Keep holding the keys down until the Message
Center displays Engineering Mode Menu. Press the Enter button to access the menu below:
a. Key Test (Will allow you to test all the keys to make sure they are functioning)
b. Security (Allows the keypad to be locked to prevent unauthorized use)
c. Functions (Press Enter to access settings and Up arrow to scroll)
i. Sleep Mode (Turn on to have the console power down automatically after 20 minutes of inactivity)
ii. Motor Test (Press Enter to run the resistance motor up and down in a continuous loop. Display shows
level setting and position sensor reading. Press Stop to end test.)
iii. Beep (Turns off the speaker so no beeping sound is heard)
iv. Units (Sets the display to readout in English or Metric display measurements)
v. ODO Reset (Resets the odometer)
vi. Pause Mode (Turn on allow 5 minutes of pause, turn off to have the console pause indenitely)
d. LCD Test (Tests all the display functions)
Adjusting The Speed Sensor
Engineering Mode Menu
1. Remove the safety key
2. Press and hold down the Start and Fast + buttons and replace the safety key. Continue to hold the
Start and Fast key until the window displays “Factory settings”, then press the Enter key.
3. You will now be able to set the display to show Metric or English settings (Miles vs. Kilometers).
To do this, press the Up or Down key to show which you want, then press Enter.
4. Make sure the wheel size diameter is 2.30 then press Enter
5. Adjust the minimum speed (if needed) to 0.5 and then press Enter
6. Adjust the maximum speed (if needed) to 10.0 and then press Enter
7. Adjust the maximum elevation (if needed) to 12 and then press Enter
8. Grade return – On (This allows the incline to return to zero when Stop is pressed. For sale in
Europe, EU standards require this to be off)
9. Press Start to begin calibration. The process is automatic; the speed will start up without warning, so
do not stand on the belt.
Calibration Procedure
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Spirit XT185 - 2011-2012 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Spirit XT185 - 2011-2012 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info