611468
55
Verklein
Vergroot
Pagina terug
1/55
Pagina verder
16, 22, 22MTK User Manual
APPENDIX 1: NO SOUND?
NO SOUND
APPENDIX 1: NO SOUND?
A Troubleshooting Guide.
Isaninputfailingtoappearatappearingatanoutput?Thebestapproachitistorstmakesurethe
inputisvalid,andthenworkthroughthesignalpathtondoutwherethe‘break’is...Checktheexact
audio path of any signal by referring to the signal path diagrams in Chapter 4.
Check Solos
If a PFL light on an input channel is lit, or the AFL/PFL ACTIVE LED (below main audio meter) then a solo is active
and all channels except those that are ‘soloed’ will be muted. This will only affect the headphones output.
Clear all active Solos by pressing any illuminated Input Channel PFL buttons and any engaged Aux Master AFL buttons.
Check Input Channel Path To Solo Bus
The channel solo can be very useful here. If you Solo the channel it will send a post-EQ, pre-Mute signal to the Solo
bus and you should be able to see signal indicated on the main meters, or hear it in the headphones.
Things that might prevent the signal getting that far include a GAIN control set too low, phantom power not switched
on for a source that requires it (condenser microphone, active DI etc), or an active SUB RTN switch on a channel
where there is no USB input (MTK models only).
Check the Input Channel routing diagram (Section 4.1) and ensure the channel controls are set up correctly.
Check Input Channel Path To Routing
If the signal is present on the Solo bus with PFL engaged, the problem might be further down the input channel. It
could be simply that the Mute is active, or the fader is down - or there could be a problem with the routing.
For a signal to go to the Main Stereo Bus or to a Group Bus, the corresponding routing switch must be engaged
(MST,1-2,or3-4).Also,apanorbalancecontrolcanhaveasignicanteffect-ifthesignalisroutedtoGroups1-2,
for example, and the pan control is full left (Group 1), you won’t hear anything from the Group 2 bus.
Check Mute and fader status, and that the channel routing selections are correct.
Check Bus Masters
If you have routed signal to the Main Stereo bus or a Group bus, or you have turned up the channel’s contribution
to an Aux bus, then the master controls for that bus must be set correctly. For example, if the signal is routed to the
Stereo master but the Stereo Master fader is down, you won’t hear anything.
Check the controls on any Bus Masters that the signal is routed to.
No FX?
For an internal FX to be heard, there must be a source contribution from a valid input. Increase the level to the FX
bus using the Aux/FX control (Aux 4/FX for Signature 16, Aux 4/FX and Aux 5/FX for Signature 22 and 22MTK.
Also, the signal is return through the corresponding FX Return Channel. Troubleshoot this signal path as you would
do for a normal input channel.
The internal FX routing has three stages - send, processor, and return. All three must be set correctly for the FX to be heard.
55

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Soundcraft-Signature-16

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Soundcraft Signature 16 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Soundcraft Signature 16 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info