23388
14
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
masterpage:Left
filename[\\B-02w2000e\SONY RM-LG112\4247243111\424724311RMLG112U\GB04ADV_RM-
LG112-U.fm]
14
GB
model name1[RM-LG112]
[4-247-243-11(1)]
If the memory of the remote is already full,
the USE MODE button flashes 8 times in
quick succession and the remote
automatically exits the learning mode.
6 Repeat steps 1 through 5 to program
up to 10 IR codes.
Tip
If programming is unsuccessful, check the following:
If the USE MODE button does not light up in step 1,
the batteries are weak. Replace both batteries.
– If the USE MODE button lights 4 times in quick
succession in step 3, an error has occurred. Start
again from step 1.
To cancel programming
Press USE MODE during any step. The remote
automatically exits the macro setting mode.
To delay the output of an IR code
Start over from step 1.
In step 3, press the easy scroll key lightly (for
less than 2 seconds). A 1 second delay is
programmed. The USE MODE button lights
twice slowly, then the remote automatically
exits the macro setting mode.
To clear the programmed IR
codes
Clear each macro step individually. In step 3,
press the easy scroll key for more than 2
seconds. The IR code is cleared. The USE
MODE button lights twice slowly, then the
remote automatically exits the macro setting
mode.
To start macro play
Move the easy scroll key to select “M1” or
“M2”, then press the key to enter the
selection
Note
If the Macro Play function does not work properly,
program a delay between each operation. See “To
delay the output of an IR code”.
You can switch the command mode (AV1 or
AV2) of the remote. If the command mode of the
receiver and the remote is different, you cannot
use the remote to operate the receiver.
1 Press ?/1 while holding down USE
MODE.
2 Move the easy scroll key to select
“MAIN”, then press the key to enter the
selection.
3 Move the easy scroll key to select
“AV1” or “AV2”, then press the key to
enter the selection.
The USE MODE button lights once (or
twice for AV2), then the command mode
switches.
To set the 2nd zone mode (North
American models only)
You can use the remote to select the input for the
2nd zone. You can use the easy scroll key only
for the 2nd zone.
1 Press ?/1 while holding down USE
MODE.
2 Move the easy scroll key to select
“2ND”, then press the key to enter the
selection.
The USE MODE button lights once, then
the command mode switches.
To reset the remote to factory
settings
Press ?/1, AV ?/1, and MASTER VOL – at
the same time. The USE MODE button lights 3
times, then goes off.
Selecting the mode of the
remote
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sony RMLG112 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sony RMLG112 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info