568042
2
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
DUAL ALARM CLOCK WITH ADJUSTABLE TONE, VOLUME, AND
VIBRATOR
MODEL SBD375ss
OPERATION INSTRUCTIONS
IMPORTANT- Please read these instructions carefully before use and retain for future
reference.
Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture. Before
connecting to mains make sure that the requirements specified on the apparatus corresponds to the
available power supply i.e. USA: AC 110V / 60Hz EUROPE: AC 230V / 50 Hz.
Features shown on diagrams above:
1) Dual Alarm Setting 7) Slow Min/Hour Button 13) Alarm 1 (AL1) Indicator
Switch 8) Snooze Button 14) Alarm 2 (AL2) Indicator
2) Dimmer Switch 9) Time Set Switch 15) Vibrator/Bed Shaker Input
3) Clock Display 10) Tone Control Wheel 16) AC Power Input
4) PM Indicator (12 hr. only) 11) Function Switch 17) Backup Battery Compartment
5) Alarm SET/OFF Switch 12) Volume Control Wheel
6) Fast Min/Hour Button
GENERAL DATA
Power: Consumption: USA: AC 110V / 60Hz EUROPE: AC 230V / 50 Hz.
UL listed transformer (Underwriters Laboratories)
Setting the correct time-
1) Depress “TIME SET” button (9)
2)
As you depress the “TIME” button (9) at the same time depressing the “FAST” (6) or the “SLOW”
(7) minute/hour button to advance clock display until you have desired time.
3) Lighted dot (4) located in upper left corner o
f clock display indicates time is PM, no light indicates
time is AM.
Setting the alarm time-
1) To set alarm AL1 slide “DUAL ALARM SETTING SWITCH” (1) to AL1 position.
2)
Depress “ALARM SET/OFF” (5) button at the same time depressing “FAST” (6) or the “SLOW”
(7) minute/hour button until you reach desired alarm setting.
NOTE: when setting the alarm time if you advance more than 24 hours the display (3) will begin to
flash and alarm will sound. To stop flashing, move “FUNCTION SWITCH” (11) up then back to
OFF position. When alarm sounds display (3) will also flash.
3) Make sure alarm time is correctly set for AM or PM (4).
4)
Once alarm AL1 has been set, slide the “DUAL SETTING SWITCH” (1) to the AL2 position.
Follow the same steps that were taken when setting alarm AL1.
5)
Once both AL1 and AL2 have been set, slide the “DUAL SETTING SWITCH” to the middle
position AL1+AL2 for both alarms.
6)
You will see two dots on the right side of the LED display; AL1 (13) and AL2 (14) to show alarms
have been enabled. Lighted dots indicate which alarm is set.
Alarm-
1)
To enable the alarm function, slide the “FUNCTION SWITCH” (11) up to the position that you
desire to wake to, you can choose “VIB” for bed shaker, “BUZZ” for sound, and “VIB/BUZZ” for
both. NOTE: whichever function you choose to wake to, will be the same function for both alarms.
Snooze Operation-
1) “SNOOZE” button (8) – press after alarm has gone off. The alarm will re-
minutes for extra sleep. You may repeat up to 54 minutes.
2) When using “SNOOZE” (8) if alarm AL1 uses snooze, it will not affect alarm AL2.
Shutting Off Alarm-
Alarm can be shut off temporary for the day or permanently shut off.
1)
When alarm AL1 goes off, press the “ALARM SET/OFF” (5) button to turn off for the day.
2) Once both alarms go off and
the “ALARM SET/OFF” (5) button has been pressed, alarms will shut
off for the day and come back on the next day at the same time if alarm settings have not changed.
3)
To shut the alarm off permanently, slide the “FUNCTION SWITCH” (11) down to the OFF
positi
on. Alarm will not come on until “FUNCTION SWITCH” (11) is set to “VIB/BUZZ”, “VIB”,
or “BUZZ” position.
Volume Control-
1) To adjust volume, rotate wheel located on the lower right bottom corner of the clock (12).
Tone Control-
1) To adjust “TONE CONTROL” (10)
turn the wheel on the top right corner of the clock to the
desired tone sound.
Bed Shaker / Vibrator-
1) Attach the bed shaker jack to the back of clock at “VIBRATOR INPUT” (15).
2) To turn on vibrator slide “FUNCTION SWITCH” (11) to “VIB” or “VIB/BUZZ” position.
3) Place vibrator between mattress and box spring.
Battery Backup-
1) To use battery back up, install a 9-
volt alkaline battery in back of clock located under the
“BACKUP BATTERY COMPARTMENT COVER” (17). Battery not included. NOTE: the LED
display will not sh
ow during power failure, but the clock will still be running and keeping proper
time until the power comes back.AC_9V Power Input-
1) Attach the “AC POWER INPUT” (16) to the back of AC-
9V IN next to “VIBRATOR INPUT”
(15); it is the smaller input of the two.
Clock Format Switch-
Located on the back of the clock this switch is a 3 position switch to set the correct time format for your
country. The format is necessary for the clock to keep the correct time otherwise the clock may run too
fast or too slow.
NOTE:
IMPORTANT: do not confuse “AC POWER INPUT” (16) with the “VIBRATOR INPUT” (15).
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sonic Alert SBD375 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sonic Alert SBD375 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Sonic Alert SBD375

Sonic Alert SBD375 Gebruiksaanwijzing - Nederlands - 2 pagina's

Sonic Alert SBD375 Gebruiksaanwijzing - Deutsch - 6 pagina's

Sonic Alert SBD375 Gebruiksaanwijzing - Français - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info