590323
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
1. MEMORISING TRANSMITTERS
1.1. Memorising Telis 1 io, Key io
Figure A
Is an io-homecontrol remote control transmitter already a
part of the installation?
YES ’go to step: B Memorising the System Key
NO ’go to step: C Programming the Telis 1 io
1.2. Memorising The System Key
Figure B
1) Place existing transmitter 1 in key transfer mode
-From the Keytis, Telis, Impresario, Composio
transmitter: press the “KEY” button for two seconds.
-Using other transmitters: refer to the instructions.
2) Briey press the “KEY” button on the Telis 1 io
transmitter.
1.3. Programming The Telis 1 io
Figure C
1) Press the “PROG” button on the Situo transmitter for two
seconds: the shutter will move briey.
2) Briey press the “PROG” button on the Telis 1 io
transmitter and the Telis 1 io indicator light will blink (for
a few seconds to one minute approximately, depending
on the number of products): programming in progress.
-When the indicator lights green and stays on and a brief
shutter motion is observed: programming complete.
-Indicator light blinks orange: programming has failed,
repeat the procedure.
2. USING THE TRANSMITTERS
2.1. Using “My” Favourite Position
Figure D
1) When all the shutters are stopped, briey pressing
the “my” button moves the shutters to your favourite
position.
2) When one of the shutters is moving, briey pressing the
“my” button stops the shutter.
2.2. Information Feedback
Figure E
1) While the shutters are moving:
-Indicator light blinks green: order in progress
-Indicator light lit green: order correctly executed
-Indicator light blinks orange: problem, one of the
shutters has not reached the requested position
(obstacle, situo in manual mode, etc).
2.3. Replacing a faulty Situo transmitter
Figure F
1) Press the “PROG” button on the Telis transmitter for two
seconds until the indicator light lights when the button is
released; the shutters will move briey.
2) Select the required shutter using the up or down buttons
on the Telis 1 io (all shutters are selected rst, then
shutter 1, 2... all shutters, shutter 1...). The selected
shutter will move briey.
3) Conrm the selection by pressing the “my” button on the
Telis 1 io for two seconds until the indicator light lights.
4) Briey press the “PROG” button on the new transmitter:
a brief shutter movement occurs, the transmitter is
memorised.
2.4. Clearing the programming
Figure G
1) Press the “PROG” button on the Telis 1 io transmitter for
two seconds until the indicator light lights.
2) Press the “my” for two seconds until the indicator light
lights.
3) Briey press the “PROG” button on the Telis 1 io
transmitter: a brief shutter movement will occur.
This procedure does not change the key setting.
2.5. Replacing The Battery
Figure H
If the “low battery” indicator light lights when the transmitter
buttons are pressed, the battery requires replacing.
Replacing the battery does not mean that the system has to
be reprogrammed.
Please separate the storage cells and batteries
from other types of waste and recycle them via your
local collection facility.
2.6. Mounting The Transmitter
Figure I
ÍR/.È4B$Î
Telis 1 io
EN Installer Manual
ES Guía de instalación
PT Instruções para a instalação
EL 
www.somfy.com
Ref.5015143B
EN
Somfy hereby declares that this product
conforms to the essential requirements and
other relevant provisions of Directive 1999/5/CE. A
declaration of conformity is available at www.somfy.
com/ce. Images are not contractually binding.
ES
Por la presente, Somfy declara que el
producto cumple con los requisitos básicos y
demás disposiciones de la directiva 1999/5/CE.
Podrá encontrar una declaración de conformidad en
la página web www.somfy.com/ce.
PT
Pelo presente documento, a Somfy declara
que o aparelho está conforme às exigências
fundamentais e às outras disposições pertinentes da
directiva 1999/5/CE. Uma Declaração de
Conformidade encontra-se disponível na Internet,
em www.somfy.com/ce.
EL
Με το παρόν έγγραφο, η Somfy δηλώνει ότι η
συσκευή συμμορφώνεται με τις ουσιώδεις
απαιτήσεις και τις λοιπές σχετικές διατάξεις της
οδηγίας 1999/5/ΕΕ. Μια δήλωση συμμόρφωσης
διατίθεται στην ιστοσελίδα www.somfy.com/ce.
SOMFY SAS, capital 20.000.000 Euros,
RCS Annecy 303 970 230 - Copyright© 2005 -
2011 Somfy SAS. All rights reserved 06/2011
EN 1. MEMORIZACIÓN DE LOS EMISORES
1.1. Memorizar el Telis 1 io, clave io
Figura A
¿Existe ya un mando a distancia io-homecontrol en la
instalación?
SÍ ’pasar a la etapa: Memorizar la clave del sistema B.
NO ’pasar a la etapa: Programar mando a distancia C.
1.2. Memorizar la clave del sistema
Figura B
1) Colocar el mando a distancia existente nº 1 en el modo
transferencia de clave
-En el caso de mandos a distancia Keytis, Telis,
Impresario, Composio: pulsar (2 s) el botón “KEY”.
-Otros mandos a distancia: consultar el manual.
2) Pulsar brevemente el botón “KEY” de Telis 1 io.
1.3. Programar Telis 1 io
Figura C
1) Pulsar (2 s) el botón “PROG” del Situo: movimiento breve
de la persiana.
2) Pulsar brevemente el botón “PROG” de Telis 1 io, el testigo
de Telis 1 io parpadea (entre unos segundos y un minuto,
aproximadamente, dependiendo del número de productos):
programación en marcha.
-El testigo permanece iluminado de color verde y la persiana
se mueve brevemente: programación efectuada.
-El testigo parpadea de color naranja: fallo en la
programación, repetir el procedimiento.
2.1. Utilizar “My” posición favorita
Figura D
1) Si todas las persianas están paradas, con una pulsación corta en
el botón “my” las persianas se sitúan en la posición favorita;
2) Si una de las persianas está en movimiento, con una pulsación
corta sobre el botón “my” la persiana se detiene.
2.2. Señalización de operaciones
Figura E
1) Durante el movimiento de las persianas:
-Testigo intermitente verde: orden en ejecución
-Testigo permanente verde: orden ejecutada correctamente
-Testigo intermitente naranja: problema, una de las persianas
no ha alcanzado la posición deseada (obstáculo, Situo en
modo manual...).
2.3. Sustituir un Situo defectuoso
Figura F
1) Pulsar el botón “PROG” de Telis hasta que el testigo se
encienda (2 s), al soltar el botón; las persianas se moverán
brevemente.
2) Seleccionar la persiana deseada con las teclas de subida o
de bajada de Telis 1 io (en primer lugar se seleccionan todas
las persianas; a continuación, persiana 1, persiana 2... todas
las persianas, persiana 1...), la persiana seleccionada hará
un movimiento breve.
3) Conrmar la selección pulsando el botón “my” de Telis 1 io
hasta que se encienda el testigo (2 s).
4) Pulsar brevemente el botón “PROG” del nuevo emisor:
la persiana se moverá ligeramente y el emisor quedará
memorizado.
2.4. Borrar la programación
Figura G
1) Pulsar el botón “PROG” del emisor Telis 1 io hasta que se
encienda el testigo (2 s).
2) Pulsar “my” hasta que se encienda el testigo (2 s).
3) Pulsar brevemente el botón “PROG” del emisor Telis 1 io:
movimiento breve de las persianas.
Este procedimiento no cambia la clave.
2.5. Cambiar la pila
Figura H
Si se enciende el testigo “pila débil” al pulsar las teclas del
emisor, hay que cambiar la pila. Al cambiar la pila no hay que
programar de nuevo.
Separe las pilas y las baterías de almacenamiento del
resto de residuos y recíclelas a través de un centro
ocial de recogida.
2.6. Fijar el emisor
Figura I
ES
PATENTS AND DESIGN PATENTS PENDING FOR
SOME COUNTRIES (e.g. : US)
A
Repeater
15 m
30 m
Repeater
15 m
30 m
Repeater
15 m
30 m
Repeater
15 m
30 m
Repeater
15 m
30 m
D1 2
F1 2 3 4
Telis 1 io
PROG
2 s
PROG
2 s
PROG
0.5 s
Situo io
Telis 1 io
PROG
2 s
PROG
2 s
PROG
0.5 s
Situo io
Telis 1 io
PROG
2 s
PROG
2 s
PROG
0.5 s
Situo io
Telis 1 io
PROG
2 s
PROG
2 s
PROG
0.5 s
Situo io
E1
Telis 1 io
OK
G1 2 3
Telis 1 io
PROG
2 s
PROG
2 s
Telis 1 io
PROG
0.5 s
PROG
Telis 1 io
PROG
2 s
PROG
2 s
Telis 1 io
PROG
0.5 s
PROG
Telis 1 io
PROG
2 s
PROG
2 s
Telis 1 io
PROG
0.5 s
PROG
C2
Telis 1 io
PROG
Situo io Telis 1 io
2 s
Situo io A/M
PROG
PROG
2 s
PROG
PROG
Situo io mobile
0.5 s
PROG
Telis 1 io
PROG
Situo io Telis 1 io
2 s
Situo io A/M
PROG
PROG
2 s
PROG
PROG
Situo io mobile
0.5 s
PROG
Telis 1 io
PROG
Situo io Telis 1 io
2 s
Situo io A/M
PROG
PROG
2 s
PROG
PROG
Situo io mobile
0.5 s
PROG
1
B21
H I
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Somfy TELIS 1 io bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Somfy TELIS 1 io in de taal/talen: Engels, Portugees, Spaans als bijlage per email.

De handleiding is 3,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info