655956
67
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
Power tool use
ENGLISH 27
x For complex cutting processes, cutting direction and order of the cuts to be performed must be specified
in advance to prevent pinching of the cut-off wheel by the removed part and injury from dropping parts.
x Always hold the power tool with both hands. Have the right hand on the rear handle, the left hand on the
top handle. Firmly grasp the handles with your thumb.
x Operate the power tool at high speed when possible.
x Direction change (cutting radius below 5 m [approx. 15 ft]), side pressure, twisting or tilting of the power
tool during cutting is forbidden.
x When shortening work pieces use a secure support and secure the work piece against slipping and
twisting. The work piece must not be held with your foot or by another person.
x Always be ready for sudden kickback of the work piece and warrant the possibility of securely backing
away.
x Make sure that cut-off sections cannot fall resulting in injury or property damage.
Always wear breathing protection equipment at dry cutting.
Metals are heated and melted at the point of contact by the fast rotation of the cut-off wheel.
x Rotate the wheel guard down as far as possible for sparks to fly forward where possible, i.e. away from
the user.
x Before cutting, specify and mark the cutting joint, and approach the material with the cut-off wheel at
medium speed. Only when the guide groove is cut, continue cutting at full throttle and increased
pressure.
x Only cut straight and vertically. Do not tilt or twist.
x For a secure and smooth cut, it is best to pull or to move the power tool in a controlled fashion. When
moving the power tool, do not push the cut-off wheel into the material in addition to the thrust caused by
the wheel's rotation.
x Large diameter round rods are best cut in steps.
x Thin tubes can be cut with a single sinking cut.
x Tubes with large diameters should be treated like large diameter rods. To avoid tilting and for better
control of the cutting process, do not let the cut-off wheel sink into the material too far. Do not allow the
mounting flanges of the cut-off wheel fastening to come into contact with the work piece. Always cut flat
around.
x Double-T carriers or angled steel should be cut in steps.
x Steel bands or steel plates are cut like tubes; pulling flat with long cutting area.
x Material under stress (supported or material in a wall) always has to be grooved slightly on the
compression side and then cut from the tension side so that the cut-off wheel is not pinched.
7.3 Working behaviour and working technique
7.4 Cutting metal
67

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 879-12 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 879-12 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info