655956
61
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
Preparing for use
ENGLISH 21
The power tool is delivered for operation of the cut-off wheel in the centre position by default. Generally,
the power tool is more balanced in the centre position, because the weight is distributed symmetrically to
the centre axis and the cut therefore is easier to guide.
If obstacles are very close to the cutting location, it may be required to install the cutting device in the outer
position so that the cut-off wheel is located farther towards the outside.
When working with the cut-off wheel in the outer position, observe the asymmetric weight
distribution! If possible, work in the centre position.
Conversion from centre to outer position
Preparation
x Put the power tool on level ground.
x Remove the cut-off wheel: Î Chap. 5.3,
page 17
x Remove the water supply line (30):
Unscrew the attachment screw (a) of the water
supply line on the right and left sides of the
wheel guard (2).
Remove both adapter pieces (b) including the
line from the wheel guard. Put down adapter
pieces including line so that the line does not
interfere with the following work steps and is not
clamped.
x Remove handle for wheel guard adjustment (3).
Loosen both attachment screws (c) of the handle
for wheel guard adjustment and remove the
handle.
x Loosen both attachment nuts (d) of the ribbed
belt cover (14).
x Turn ribbed belt tension screw (13) towards the
left, e.g. counter-clockwise, to reduce the ribbed
belt tension.
Turn until the square nut (e) has been moved
towards the mark "" (f) as far as possible.
When installing the cutting device in the centre
position (cf. figure), the square nut is all the way
to the left; in case of installation in the outer
position, it is located all the way to the right.
x Remove both attachment nuts (d) entirely.
x Remove the ribbed belt cover (14).
Remove wheel guard (2)
x Carefully move the wheel guard towards the
motor unit. The screws (g) of the assembly
flange (j) are moved within the oblong holes.
x Once the wheel guard has been moved towards
the motor unit until the ribbed belt support (i) can
be pulled through the ribbed belt (h), remove the
wheel guard. Observe that the ribbed belt is not
damaged by this.
5.8 Relocate cutting device from centre position to outer position
2
3
30
a
b
c
e
14
f
d
13
61

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 879-12 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 879-12 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info