655956
57
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
Preparing for use
ENGLISH 17
x Push on outer mounting flange (c) so that the curved side points southwards, i.e. away from the cut-off
wheel.
x Push on wheel (b) and turn in cut-off wheel attachment screw (11).
x Insert blocking pin (a) entirely into the blocking opening (12) and firmly tighten (30 Nm [22.1 ft·lbf]) the
cut-off wheel attachment screw (11).
Securely hold the power tool at the top handle with one hand and push it firmly onto the ground.
x Remove the blocking pin (a).
The power tool's spindle is designed for cut-off wheels with an inner bore of 20 mm.
For proper installation of cut-off wheels with a 1" inner bore, the spindle adapter disk is required that
is included with the delivery of the power tool.
The spindle adapter disk ensures correct fit of the 1" cut-off wheel on the spindle.
x Installation of cut-off wheels with 1" inner bore
takes place according to chap. 5.1 as of page 16.
x After applying the cut-off wheel on the spindle,
however, the spindle adapter disk (e) must be
put on the spindle (f) additionally.
x Put the spindle adapter disk (e) onto the spindle
so that it inserts between spindle and inner bore
of the cut-off wheel.
The support area of the spindle adapter disk
must point outwards in the installed condition,
i.e. away from the spindle.
The correct orientation of the spindle adapter
disk is mandatory to directly connect the plane
inner area to of the outer mounting flange to the
cut-off wheel. Only this warrants secure
attachment of the cut-off wheel.
x Application of the outer mounting flange and all
following steps must be performed again
according to chap. 5.1.
x For cut-off wheel removal, the power tool must be put securely on the ground. Securely hold the power
tool at the top handle with the left hand and push it firmly onto the ground. Î Chap. 5.4, page 18
x Insert blocking pin (a) entirely into the cut-off wheel blocking opening (12) to block the spindle.
Unscrew cut-off wheel attachment screw (11).
Remove wheel (b) and outer mounting flange (c) (also see chap. 5.1).
x Remove cut-off wheel from the spindle. For cut-off wheels with a 1" inner bore, the spindle adapter disk
also must be removed from the spindle.
x Put the outer mounting flange back onto the spindle so that the curved side points outward.
x Put on wheel (b) and turn in the cut-off wheel attachment screw (11) again. Î Chap. 5.1.
x Insert blocking pin (a) entirely into the blocking opening (12) and firmly tighten (30 Nm [22.1 ft·lbf]) the
cut-off wheel attachment screw (11) again.
Securely hold the power tool at the top handle with one hand and push it firmly onto the ground.
x Remove the blocking pin (a).
5.2 Installing cut-off wheels with 1" inner bore
5.3 Removing the cut-off wheel
57

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 879-12 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 879-12 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info