619690
11
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
10
Installing your Snooper S3 using the Windscreen Suction Cup
bracket
If you prefer you can mount your S3 to the inside of your vehicles
windscreen using the suction cup bracket provided. Simply select a
position within the windscreen so that the top of the unit has a clear view
of the sky, remembering that you need to connect both the power and
RLD (If required) connection cables as well as ensuring that you can read
the LED display and reach the controls safely. Follow these instructions
to mount the unit in this way.
- Install the suction cups onto the bracket by fitting them into it’s holes.
- Clean the area where you wish to position the bracket thoroughly with a
good quality glass cleaner.
- Carefully bend the bracket so that when it is mounted on to the
windscreen with the S3 attached, the Control Panel is facing in the
desired direction so that you can easily see the LED display and
safely operate the controls.
- Slide the S3 onto the bracket until it is secure and the unit is positioned
in as horizontal a position as possible.
-To remove the S3 simply slide the unit off the bracket from the front.
- Finally plug the smaller plug on one end of the power cable into the
socket marked DC12V on the back off the S3 and plug the larger plug
into the cigarette lighter socket of your vehicle. Your Snooper S3 is now
ready for use. For further information please read the section on Power
Connection on page 11.
RS232
RD
17
Operating Instructions
1. Starting Up
After you have successfully installed your S3 and performed the download
it is time to perform the first start up. Firstly make sure your vehicle is
parked in as open a space as possible, clear of tall trees and buildings so
that the built-in GPS antenna has a clear view of the sky above. Next
power the unit up by turning the on/off/volume towards you. The S3 will
go through a brief self test procedure and then a red LED will scan back
and forth across the display indicating that the unit is searching for
satellite connection. The S3 needs to acquire a minimum of 3 satellites to
work effectively, once this has been achieved the S3 will proceed to the
standby screen with just the green letter ’P’ illuminated. As soon as the
standby screen is being displayed your S3 is ready for use and will now
automatically alert you of any locations stored in it’s database as well as
laser alerts and radar alerts if you have a S100-RLD connected.
As the GPS engine and antenna have never been used before, the first
’Cold’ start up could take somewhere between 5 - 30mins. Once
initialised, subsequent start ups will take as little as 3 mins.
2. Cancel Button
If during an alert you decide that you would like to cancel it, simply press
and hold the ’Cancel’ button. The display will automatically return to the
Standby screen and the device will be ready to alert you the next time
you encounter a stored co-ordinate or laser source.
3. Mute Button
If during an alert you decide that you would like to mute it, simply press
the ’Mute’ button briefly. The screen will continue to display a visual alert
but no sound will be heard. After you have travelled out of range of the
location the device will automatically reset so that next time you
encounter a location you will receive both audible and visual alerts as
normal.
CANCEL
NEW LOCATION
MUTE
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Snooper S3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Snooper S3 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info