335579
9
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
Instructions for the user
26
7.2.8 Timer (on some models only)
Some models are equipped with a 1 to 99-minute cooking timer.
To use the timed cooking, first set the power level by following the instructions given in paragraphs
“7.2.2 Single Cooking Zones” and “7.2.3 Dual Cooking Zones”.
Now, with the hob NOT locked out (if it is locked out, press the
key to enable the functions), press
the symbol
.
Between the symbols
and of the first active cooking zone, a LED light will turn on to indicate that
the minutes to be set will refer to operation of that particular zone.
The automatic operation minutes of the cooking zone can be increased or decreased by using the
and
keys beside .
After 5 seconds have gone by since the last time it is pressed, the timer will start and the cooking zone
will operate until the display above the symbol
reaches 0.
At this point the cooking zone will automatically turn off.
It is also possible to use the timed cooking function on more than cooking zone at the same time.
Once the timer is set on the first zone, press
key to shift the timer controls over to the next active
zone (the LED light between the symbols
and of the second active cooking zone will be
activated) and then set the cooking duration as previously described.
When the timed cooking is active on several cooking zones at the same time, the display between the
symbols
and of the cooking zone will alternatively turn on and at the same time the minutes
display found on the symbol
will show the time remaining for the zone with the LED light on.
7.2.9 Modifying the data set
During timed cooking, each single pressure on the
and symbols increases or reduces the power
of the cooking zone.
To change the remaining time of a zone, you have to press
key until the LED light in the cooking
zone turns on. Now it will be possible to change the operating time by working with the symbols
and
of the timer.
7.2.10 Residual heat
Each cooking zone is equipped with a residual heat warning device. After any zone is switched off, a
flashing “
”may appear on the display. This warns that the cooking zone concerned is still very hot.
Cooking can be restarted while the
is flashing; proceed as described in points “7.2.2 / 7.2.3”.
7.2.11 Control circuit board thermal protection
If the cooking zones cause overheating of the internal electronic circuit board, the heat will be switched
off automatically. This switches off power to the front zones, and the letters
and flash alternately
on the power leds. If the circuit board does not cool down, power to all the cooking zones is switched
off, and the power leds display the text
. Cooking can be resumed once the temperature
has dropped below the safety threshold.
7.2.12 Operator Error
If the user makes a mistake when using the push-buttons, an
appears on the power display; it will
remain there as long as the user continues to press the button being used incorrectly.
7.2.13 Switching off the cooking zones
The cooking zones are switched off when the operational power display indicates 0. The zone will
automatically deactivate 5 seconds after the display shows 0.
If the cooking zones are hot, the blinking residual heat
” will appear after they are switched off.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Smeg se 2640 tc1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Smeg se 2640 tc1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Smeg se 2640 tc1

Smeg se 2640 tc1 Gebruiksaanwijzing - Nederlands - 15 pagina's

Smeg se 2640 tc1 Gebruiksaanwijzing - Deutsch - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info