536967
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Chamberlain
®
Lift-Master
®
Sears
®
Wayne Dalton
®
Master Mechanic
®
Genie
®
(9 positions)
Genie
®
(12 positions)
Overhead Door
®
Pulsar/Allister/Allstar
®
Master Craft
®
Linear
®
M-O-M
®
Stanley
®
Multi-Code
®
Skylink
®
UR-100
The model 68 transmitter
has 12 columns of posts,
each column has 3 posts.
(see diagram C)
2a. To program the model
68, open the case with
a coin. (see diagram B)
2b. There are 2 ways to pro-
gram the model 68 so
that it will communicate
with your garage door
opener. Open your exist-
ing transmitter, (the unit
you currently use to open
your garage), or look at
the back of your garage
door opener. If you see a
column of small switches
go to point 2c in this
manual. If there are no
switches, go to point 2e.
Diagram B
Each column contains one
connector (see digram D)
for a total of 12 connectors.
Diagram D
Diagram E
If the connector is placed
on the top and middle posts,
that column is set on “ + ”
or “ON” or “CLOSE”. If the
connector is placed on the
middle and bottom posts,
that column is set on “ - ”
or “OFF” or “OPEN”. If the
connector is removed
completely, (not placed
on any posts), it is set
to “ 0 ” or the neutral
position. (see diagram E
for examples of how to
set a column to the three
different positions). When
removing a connector to
set a column to the neu-
tral position, save the con-
nector in case you change
the code at a later date.
2c. To move the connectors,
slide an opened paper clip
into the side of a connector
and lift. (see diagram F)
When repositioning con-
nectors, place a connector
on the two chosen posts,
then push down on the
connector with your finger.
Paper
Clip
Diagram F
Diagram C
USA
CANADA
A
390
390
B
318
318
C
310
315
D
300
310
STEP 2 - SET CODE CONNECTORS
Linear * Position 1 to 8 + OR -
M-O-M * Position 1 to 8 + OR -
Stanley (310) Canada Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’
Stanley (300) Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’
Multi-Code Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’
Chamberlain Position 1 to 9 +, 0 (blank), OR -
Lift-Master Position 1 to 9 +, 0 (blank), OR -
Sears Position 1 to 9 +, 0 (blank), OR -
Wayne Dalton Position 1 to 9 +, 0 (blank), OR -
Master Mechanic Position 1 to 9 +, 0 (blank), OR -
Genie (9 positions) Position 1 to 9 + OR -
Genie (12 positions) Position 1 to 12 + OR -
Master Craft Position 1 to 12 + OR -
Pulsar/Allister/Allstar Position 1 to 9 +, 0 (blank), OR -
Overhead Door Position 1 to 9 +, 0 (blank), OR -
Code connector setting to match your opener/motor
1a. Locate frequency
switch on the bottom
of the transmitter:
(see diagram A)
Diagram A
1b. Determine the brand of your garage door
opener and set the frequency switch to the
corresponding position. (see chart 1)
STEP 1 - SET FREQUENCY SWITCH
Thank you for your purchase of the Skylink garage door
remote control, Model 68. There are 2 different steps
you need to setup in order to use this universal garage
door remote control to operate your existing garage door
opener. These 2 steps are:
1) Frequency switch – select the correct frequency
according to the brand of your existing garage door
opener.
2) Code setting – Set the jumper connectors on the
Model 68 so that they match the code setting of your
existing garage door opener.
Please follow the detailed instructions below in order to set-
up the Skylink Model 68 to work with your existing opener.
NOTE: Transmission range may be reduced with use
on a metal garage door.
PROGRAMMING THE TRANSMITTER
Diagram G
Set the connectors numbered 1 through 12 to match the
switches of your existing transmitter or receiver. If your
garage door opener is manufactured by (Stanley
®
, Genie
®
,
Multi-Code
®
, Linear
®
, Moore-O-Matic
®
) these switches
may only have two positions, (“ +, ON, CLOSED” and “ - ,
OFF, OPEN”). (see diagram G) Set the connectors on the
model 68 to “ + ” if your existing switches are either “+ ,
ON, CLOSE ” and set to “ - ” if your existing switches are
either “ -, OFF, OPEN”. Do not use the center position “ 0 ”.
Examples of how to set Model 68
*Please check the FAQ section from www.skylinkhome.com for very old Linear / M-O-M systems.
Chart 1
390
390
390
300/390
390
390
390
390
318
-
310
310
300/310
300/310
390
A
A
A
D/A
A
A
A
A
B
-
C
C
D/C
D/C
A
315/390
315/390
315/390
315/390
315/390
315/390
315/390
315/390
318
315/390
310
310
310
310
390
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
B
C/A
D
D
D
D
A
Brand of your opener
Set switch
to position
Set switch
to position
Frequency
Frequency
USA CANADA
Model 68
Existing
Transmitter
‘+’ or ‘ON’ or CLOSE ‘0’ = BLANK
‘-’ or ‘OFF’ or ‘OPEN’
STEP 2 - SET CODE CONNECTORS
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skylink 68 - remote bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skylink 68 - remote in de taal/talen: Engels als bijlage per email.

De handleiding is 0,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info