479936
6
Verklein
Vergroot
Pagina terug
1/45
Pagina verder
6
INTRODUCTION
This tool is intended for hammer drilling in brick,
concrete and stone as well as for drilling in wood, metal,
ceramic and plastic; tools with electronic speed control
and left/right rotation are also suitable for screwdriving
and thread cutting
TECHNICAL SPECIFICATIONS 1
OPERATING CONTROLS 234
A Switch for on/off and speed control
B Button for switch locking
C Wheel for maximum speed control
D Switch for changing direction of rotation
E Switch for selecting drilling function
F Wheel for maximum speed control/torque control
G Switch for selecting drilling/screwdriving position
H Spindle-lock button
SAFETY
Read and save this instruction manual (pay special
attention to the safety instructions at the back)
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Always keep the cord away from moving parts of the tool
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
SKIL can assure flawless functioning of the tool only
when original accessories are used
Before using accessories always compare the maximum
allowed r.p.m. of that specific accessory with the r.p.m.
of the tool
This tool should not be used by people under the age of
16 years
Be careful not to drill or drive into areas where electrical
wires may be contacted
The noise level when working can exceed 85 dB(A);
wear ear protection
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
Never use tool when cord is damaged; have it replaced
by a qualified person
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
If the drill bit becomes unexpectedly jammed (causing a
sudden, dangerous reaction), immediately switch off the
tool
Be aware of the forces that occur as a result of jamming
(especially when drilling metals); always hold the tool
firmly with both hands and take a secure stance
Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
On/Off 5
Switch locking for continuous use 6
Speed control for smooth starting 7
Maximum speed control
With wheel C/F the maximum speed can be adjusted
from low to high (1-5)
6460/6463/6464 23
- switch on the tool
- lock the switch
- turn wheel C to select maximum speed
6466 4
- set switch G in drilling position
- switch on the tool
- turn wheel F to select maximum speed
Torque control (6466) 4
With wheel F the amount of torque delivered by the
chuck can be adjusted steplessly from minimum to
maximum (1-5)
- set switch G in screwdriving position (maximum
speed is adjusted automatically)
- switch on the tool
- turn wheel F to select torque
- to prevent overtightening of screws, always start with
low torque and adjust accordingly
When torque has reached its adjusted value, the rotation
of the chuck will stop; if subsequently load is removed
from the tool while the on/off switch is still activitated,
the tool continues to run at very low speed for safety
reasons; release switch A briefly to resume operation
Changing direction of rotation 8
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Normal drilling/screwdriving versus hammer drilling 9
! select drilling function only when tool is switched
off
Changing bits 0!@
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
! push spindle-lock button only when tool is at a
complete standstill @
Adjusting drilling depth #
Holding and guiding the tool $
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the
tool do the work for you
GB
XP SKIL 6460/6463/6464/6466 12-06-2002 16:29 Pagina 6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 6463 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 6463 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info