644809
8
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
8
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR RECIPROCATING SAWS
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
SKIL can assure awless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
This tool should not be used by people under the age of
16 years
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
Keep hands away from cutting area and the blade;
keep your second hand on barrel grip J 2 (if both
hands are holding the saw, they can not be cut by the
blade)
Do not reach underneath the workpiece (the proximity
of the blade to your hand is hidden from your sight)
Never hold piece being cut in your hands or across
your leg (it is important to support the work properly to
minimise body exposure, blade binding, or loss of control)
Use clamps or other equipment to secure and
support the workpiece (holding the workpiece in your
hand or against your body may lead to loss of control)
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord (contact with a
“live” wire will also make exposed metal parts of the tool
“live” and shock the operator)
Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to re or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
Do not use a dull or damaged blade (bent blades can
break easily or cause kickback)
Keep hands away from between the tool housing
and blade clamp E 2 (the blade clamp can pinch your
ngers)
Ensure that blade clamp E 2 is tight before making
a cut (a loose clamp may cause the tool or blade to slip
with loss of control as a result)
Wear protective glasses and hearing protection 4
Use protective gloves when removing the blade from
the tool (the saw blade may be hot after prolonged use)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
On/o 5
Speed control
With wheel C 2 the sawing speed can be adjusted from
low to high (6 positions)
Adjusting sawing speed to material used 6
! if the tool does not run with wheel C 2 in position
1, select a higher sawing speed and lower the
sawing speed while the tool runs
Mounting saw blade 7
! disconnect the plug
- press blade clamp E forward and hold it in that position
- insert blade (with teeth facing down or up) to full depth
- release blade clamp E
- pull out blade somewhat until clamp E clicks into a
square position
- push in and pull out blade to check whether it is locked
correctly
! ensure that blade clamp E 2 is tight before
making a cut (a loose clamp may cause the tool
or blade to slip with loss of control as a result)
! ensure that the front end of the blade extends
through footplate F for the entire stroke length
Removing saw blade 8
- press blade clamp E forward and hold it in that position
- pull out blade
- release blade clamp E
Orbital action for fast cutting 9
- for activating the orbital action of the saw blade use
switch D as illustrated
! do not activate the orbital action when cutting metal
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 4960 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 4960 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 6,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info