591170
7
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
7
USE
Cord restraint 8
- hook the loop in the extension cord over restraint A as
illustrated
- pull tight to secure the extension cord
Two-hand safety switch 9
Prevents the tool from being switched on accidentally
- switch on the tool by pressing both switch B and
switch C
- switch o the tool by releasing either switch B or
switch C
Operating the tool
! starttrimmingonlywhenmotorisrunning
! donotcutgroundcoveringplantsinorderto
preventearth/sandfromdamagingcuttingbladesD
! donotoverloadthetoolbycuttingstemslarger
than14mminthickness
- move tool away from cutting area before switching o
! afterswitchingoffthetoolthebladescontinueto
moveforafewseconds
Blade tip protector F 2
- prevents kickback of the tool when solid objects (such
as fence posts or house walls) are touched
- protects the end blades from damage
Trimming hedges 0
- trim the sides of the hedge rst (from the bottom
upwards), then cut the top
- trim the side of a hedge in such a way that it will be
slightly narrower at the top
- use a hand saw or pruning shears to cut thicker
branches
Holding and guiding the tool
- hold the tool rmly with both hands and take a secure
stance
! whileworking,alwaysholdthetoolatthe
grey-colouredgriparea(s)!
- guide the tool ahead of you
- always ensure that the extension cord is guided away
from the work area
- start trimming near the mains socket and move away
while working
APPLICATIONADVICE
For trimming a hedge at a uniform height level
- fasten a piece of string along the length of the hedge
at the desired height
- trim the hedge just above this string
Recommended cutting/trimming times (Western Europe)
- trim hedges with deciduous leaves in June and
October
- trim evergreen hedges in April and August
- trim conifers and other fast-growing shrubs every 6
weeks from May until October
MAINTENANCE/SERVICE
This tool is not intended for professional use
Keep tool, cord and cutting blades clean
! disconnecttheplugbeforecleaning
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- clean ventilation slots G 2 regularly with a brush or
compressed air
- after use, always carefully clean and lightly lubricate
the cutting blades
! weargloveswhenhandlingorcleaningthe
cuttingblades
Regularly check the condition of the cutting blades and
the tightness of the blade bolts
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
Sharpening the cutting blades
! disconnecttheplugbeforesharpening
- sharpen the cutting blades with a small and smooth
le, in case a solid object damaged them
- we advise you, however, to have the blades sharpened
by a specialist
- lubricate the cutting blades after sharpening
Storage @
- securely mount storage rail H on the wall with 4 screws
(notsupplied) and horizontally leveled
- use blade cover J when storing the tool
- before storing the tool, wipe o the cutting blades with
an oil-soaked rag to prevent corrosion
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switchoffthetoolanddisconnecttheplugbefore
investigatingtheproblem
Motor does not start or stops suddenly
- power supply socket faulty -> use another socket
- plug not connected -> connect plug
- extension cord damaged -> replace extension cord
Tool operates intermittently
- extension cord damaged -> replace extension cord
- internal wiring defective -> contact dealer/service
station
- on/o switch defective -> contact dealer/service
station
Motor runs but blades remain stationary
- internal fault -> contact dealer/service station
Cutting blades hot
- cutting blades blunt -> have blades sharpened
- cutting blades have dents -> have blades inspected
- too much friction due to lack of lubricant -> lubricate
blades
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 0740 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 0740 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 7,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info