570580
10
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
TO REGULATE TAKE-UP LEVER
WITH REGULATOR INDICATOR
The spring tension on take-up lever J, Fig. 29 is adjusted
by thumbnut K. The tension on this lever should be about
the some as that applied to the upper thread by the tension
discs.
When the stitch is set, at the top of the needle bar stroke,
lever J should be held down for enough by the tension of
the thread so that the take-up action will keep the thread
tout until the needle enters the work.
When sewing lightweight materials with fine thread, more
take-up action may be secured by turning the thumbnut K
so that it screws up to decrease the take-up spring tension.
This should be done instead of tightening the thumbnut of
the tension discs.
For heavier materials and thread, the take-up tension must
be about the some as that applied to the upper thread by
the tension discs.
The travel of take-up lever J is regulated by means of
knurled nut L. The indicator near nut L is marked with the
figures O to 4. This indicator provides a useful guide to
the operator in setting the take-up movement most suitable
for the material and thread being used. For thin materials,
such as kid or box calf, turn knurled nut until the zero
mark is opposite the small plunger U.
Other adjustments can be made in steps by turning the nut
to suit any thickness of material and thread within the
capacity of the machine.
NOTE: All machines sent out from the factory are so
adjusted that they will give satisfactory results on a
general range of materials. Before any adjustment is made
to the travel of the take-up lever, the needle bar should be
raised to its highest point.
Fig. 29. Regulating Tension and Travel of Take-up Lever
ADJUSTMENT OF THREAD TAKE-UP
LEVER REGULATOR INDICATOR
The range of adjustment given by the indicator, when sent
out from the factory, should suffice for all general
purposes, but, if desired, the range can be raised or
lowered by means of the adjusting screw T, Fig. 29 at the
extreme right.
To alter the range, loosen the lock nut S and, using a
screwdriver, turn the centre screw T to the right to reduce
the travel of the take-up lever.
To increase the travel, turn the screw T to the left. Wear at
the tip of the centre screw can also be taken up in this
manner. When the proper adjustment has been obtained,
tighten the lock nut S.
It is most important that the hexagon head nut R be
securely locked against the face of the piston.
TO CHANGE LENGTH OF STITCH
The length of stitch is regulated by the stitch regulator
which is held in position by thumbscrew M, Fig. 30 at
back of the feeding foot bar. Loosen thumb screw M and
move the regulator up or down until its top is in line with
the mark indicating desired number of stitches to the inch
as shown by the arrow. Then tighten the thumb screw.
Fig. 30. Changing Stitch Length
10
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Singer-29K71

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Singer 29K71 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Singer 29K71 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info