634624
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Mounting location of base station
Avoid installing the base station behind other electrical and electronic devices, as
they may interfere with the signal and consistency of wireless communication.
The base station should be at least 2 meters away from any other Bluetooth or wire-
less LAN (WiFi) transceiver.
It is advisable to check Bluetooth connection throughout the boat by pairing the
unit before permanently mounting the base station.
Operation
Keys and LED Action Mode: Auto Standby Wind NoDrift
< Left arrow Port or
> Right arrow Starboard
Short press: Adjust 1° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind mode.
Long press (2s): Adjust 10° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind
mode.
< Left arrow +
> Right arrow
Autotack (in Wind mode), press and hold until LED is flashing green rapidly, then press AUTO to confirm.
STBY Place the autopilot into Standby mode.
MODE Changes the autopilot mode:
1. Boats set to SAIL: Toggles AUTO and WIND modes.
2. Other boat types: Toggles AUTO and NoDrift modes.
AUTO Engages the autopilot into AUTO mode.
LED* Green for 1s indicates message acknowledged. Red for 1s indicates message is either rejected or not acknowledged.
Green rapid flashes for up to 10s, followed by solid green for 1s. Red for 1s indicates message is either rejected or not
acknowledged.
* Note: In addition to the LED behaviour specified: Red will flash for 1s every 10s when battery level is low.
X X
X
X
Electromagnetic
Interference
0.5 m (20”) Min 0.5 m (20”) Min
2 m (6 ft) Min
RADAR
Magnetic Field
Radio Transmitter
X
Surface mount the base station
3 mm
19 mm
1
4
5
3
2
Use of Lanyard strap or wristband Add/replace batteries
WR10 Wireless Autopilot Controller operates
on 2 AAA batteries. Remove the cover to add
or replace the batteries.
Wiring the base station
A
1.8 m (6 ft) Micro-C drop
cable (male to female)
B
Micro-C T-Joiner
C
Micro-C backbone
A
B
C
First, make sure that:
- the batteries in the remote are not low.
- the remote and the base station are placed as close together as possible.
- the AP system is OFF or in standby.
Then continue to:
1. Remove power from the base station.
2. Press and hold the buttons MODE and STBY on the remote for at least 5 seconds
until a single quick green LED flashes. The remote is now in Discoverable mode and
will stay in this mode for 60 seconds or until base station asks to pair.
3. Power up base station. For the first 10 seconds, the base station will search for
Discoverable remotes.
4. Wait till remote quickly flashes the green LED every second, indicating that the base
station is asking to pair.
5. Press the AUTO button for at least 1 second to start the pairing.
- When succesfully paired: The green LED will stay on for 2 seconds.
- When pairing failed: The red LED will stay on for 2 seconds.
Pairing a remote to the base station
Use Philips screw-
driver size #1 to en-
sure proper torque
when reassembling.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Simrad WR10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Simrad WR10 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info