634386
62
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
62 |
The alarm system | AP70/AP80 Installation Manual
Alarm/Warning Type Warning/Alarm condition Possible cause and recommended action
Red flashing AP70/
AP80 power button,
black display
A < 5 V
Local supply voltage to AP70/AP80 missing or <5 V.
Check local supply, connections and fuses to AP70/AP80
control units
Active control unit
missing
A
Autopilot computer has
lost contact with active
control unit
Active control unit goes silent.
1. Check/repair CAN bus cable
2. Replace the control unit
Autopilot computer
missing
A
Active control unit has
lost contact with autopilot
computer
Faulty autopilot computer or poor cable connections from the
same.
1. Check connectors and cable
2. Check local power to control unit
3. Check that control unit is turned on
4. Replace autopilot computer
¼ Note: Since this alarm may be given by several units at the
same time, it has no device tag.
Boat speed missing W/A Lost sensor data
The speed signal from the GPS or the log is missing.
1. Check Device list for valid speed source
2. Try a new automatic source update
3. Check the GPS, log, and cable connections
CAN bus failure A
Not possible to send or
receive data although bus
voltage is ok
Poor CAN bus backbone, defective cable/connector or
defective CAN bus receiver in autopilot control unit.
1. Check backbone terminations
2. Check cable and connectors
3. Replace Autopilot control unit
CAN bus supply
overload
W Current >4.3 A Check summary unit loads
A
Current >10 A for 1 ms,
hw shutdown
Excessive current draw.
Check for short circuit/defective device on network.
Check heading A
Lasting steering compass
heading jump >10° within
1 sec during automatic
steering
A sudden jump in heading of more than 10 degrees is
detected
Check steering compass. Possibly change to other heading
source or monitor compass.
Compass difference A
Difference between
steering compass
and monitor compass
+variance > set limit
The difference in readings between the main compass and
the monitor compass exceeds the limit set for “Compass
difference”.
Check the operation of both compasses. If one compass is
magnetic, the error may be caused by deviation change or
heavy sea disturbances.
Course difference A
Actual heading diff from
track course by set limit
Compass heading is deviating too much from the track
course (BWW). May be caused by extreme wind and current,
combined with low speed.
Cross track distance
limit
W/A XTD > XTD limit
XTD has reached set XTD limit in NAV/TRACK mode. May be
caused by extreme wind and current or too low boat speed.
Drive inhibit A
Motor or solenoid drive
electronics critically
overloaded
Check for wire shortage, eventually disconnect suspicious
wires.
No drives available A
None of the drives
selected in present work
profile is available for
steering
Check that use of thruster(s) has been activated by CMD/
THRUSTER button.
Check that steering gear/thruster is started and set for
autopilot control.
Check if speed is below thruster inhibit limit.
Check if drive is unavailable for other reason (ref. Drive ready
missing alarm).
62

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Simrad AP80 Autopilot bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Simrad AP80 Autopilot in de taal/talen: Engels als bijlage per email.

De handleiding is 19,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Simrad AP80 Autopilot

Simrad AP80 Autopilot Aanvulling / aanpassing - English - 18 pagina's

Simrad AP80 Autopilot Snelstart handleiding - English - 6 pagina's

Simrad AP80 Autopilot Gebruiksaanwijzing - English - 72 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info