620427
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Operating Instructions
RDD10.1DHW
RDD10.1DHW is a temperature controller that allows you to set the ideal room temperature at the
time you want and with independent control of DHW (Domestic Hot Water). There are 3 operating
modes available. You can either rely on the factory settings or make settings that suit your
personal needs.
Display
Operation and settings
Warmer / colder
setting the
temperature setpoints
DHW ON/OFF
Changing the
operating mode
between normal
operation, energy
saving and frost
protection mode
Room temperature or setpoint
Batteries
3033Z05en
1.5V
'AA'
1.5V
'AA'
+-
Normal operation
Energy saving mode
Heating ON
Room temperature
Replace batteries
DHW equipment ON
Frost protection mode
Commissioning
The controller is supplied with factory-set temperatures and operating mode. To commission
it, proceed as follows:
1,5 V
"AA"
1,5 V
"AA"
Remove the black transit tabs from the 2 batteries. Check to see if the battery holder
is in its correct position. The controller switches itself on.
Do you want to change the operating mode?
By pressing , you can change the operating
mode. The sequence is started from normal operation,
energy saving mode and frost protection, or vice versa.
Then, the setpoint of the selected operating mode will
be maintained.
In normal operation, the display shows
, in energy
saving mode, the display shows
, and in frost
protection mode, the display shows
.
Default operating mode is “Normal operation”.
When the unit is first powered up,
the display shows
.
Are your rooms too warm or too cold?
+
To increase or decrease the room temperature
setpoint in increments of 0.5 °C, proceed as follows:
Press
to select the operating mode
corresponding to the set point that you want to
change
Press
+
or once
The setpoint display starts flashing
Press these buttons again to change the
temperature setpoint in the range 5 ... 35 °C
5 seconds after the last push, the new temperature
setpoint will automatically be saved. The display stops
flashing and shows the room temperature currently
measured.
Note:
The setpoint in energy saving mode can be set to
0 °C. This means OFF or, in other words, the
controller is not active in energy saving mode and
symbol
will not appear on the display.
Risk of frost!
If you want to have frost protection, press
to
select frost protection mode, the display shows
and default value is 5 °C. If the room temperature falls
below the preset frost protection level, it will
automatically activate the heating output.
CE1B3033en / 18.11.2005 Subject to alteration Building Technologies / HVAC Products
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens RDD10.1DHW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens RDD10.1DHW in de taal/talen: Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens RDD10.1DHW

Siemens RDD10.1DHW Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens RDD10.1DHW Installatiehandleiding - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info