61045
9
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
7
Gigaset AS150 / English / A31008-M1811-R601-3-TN19 / Wytana.fm / 05.05.2008
Care
Wipe the base station, charging cradle and handset
with a damp cloth (do not use solvent) or an anti-
static cloth.
Never use a dry cloth. This can cause static.
Contact with liquid
If the handset has come into contact with liquid:
1 Switch off the handset and remove the bat-
tery pack immediately.
2 Allow the liquid to drain from the handset.
3 Pat all parts dry, then place the handset with
the battery compartment open and the keypad
facing down in a dry, warm place for at least
72 hours (not in a microwave, oven etc.).
4 Do not switch on the handset again until it is
completely dry.
When it has fully dried out, you will normally be
able to use it again.
Questions and answers
If you have any queries about the use of your tele-
phone, go to
www.siemens.com/gigasetcustomercare
for assistance 24/7. The table below contains a list
of common problems and possible solutions.
Authorisation
This device is intended for analogue phone
lines in your network.
Country-specific requirements have been
taken into consideration.
We, Siemens Home and Office
Communication Devices GmbH & Co. KG,
declare that this device meets the essential
requirements and other relevant regulations
laid down in Directive 1999/5/EC.
A copy of the 1999/5/EC Declaration of
Conformity is available at this Internet
address:
http://www.siemens.com/gigasetdocs
.
Problem Cause Solution
Nothing
appears in the
display.
The handset is not
switched on.
Battery pack is
flat.
Press the end call
key
a for approx.
5seconds or place
the handset in the
base.
Charge/replace the
battery pack (page 2).
No response
to key press,
"HOLD KEY"
appears in the
display.
The keypad lock is
activated.
Press the hash key
R
for approx. 2 sec
(page 3).
No wireless
connection to
the base, dif-
ferent icons
flash in the
display.
The handset is
outside the range
of the base.
The handset is not
registered.
The base is not
switched on.
Cords not routed
correctly
Move the handset
closer to the base.
Register the handset
(page 4).
Check the power con-
nector at the base
(page 2).
Check cord routing
(page 2).
You cannot
hear a ring/
dialling tone
from the fixed
network.
The supplied
phone cord was
not used or it has
been replaced by
a new cord with
the wrong pin
assignment.
Please always use the
supplied phone cord
and ensure that the
pin connections are
correct when purchas-
ing a new one
(page 2).
!
Error tone
after entering
system PIN.
Forgot PIN
The system PIN
entered is incor-
rect.
Restore the system
PIN to the factory set-
ting (0000). To do this
disconnect the mains
unit
¢hold down the
paging-key ¢recon-
nect the mains unit
¢
hold the paging key
down for at least a
further 2 seconds
then release it.
The resetting proce-
dure is carried out.
The handsets are
deregistered. The
calls list is deleted.
Problem Cause Solution
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Siemens-AS150

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens AS150 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens AS150 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens AS150

Siemens AS150 Gebruiksaanwijzing - Nederlands - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info