63603
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
9
L1a / GBR / A31008-M2001-L101-1-7619 / AL140_AL145_Kombi_GBR.fm / 13.08.2007
Base station power consumption
General specifications
Care
Wipe the base station, charging cradle and hand-
set with a damp cloth (do not use solvent) or an
antistatic cloth.
Never use a dry cloth. This can cause static.
Contact with liquid
If the handset has come into contact with liquid:
1. Switch off the handset and remove the bat-
tery pack immediately.
2. Allow the liquid to drain from the handset.
3. Pat all parts dry, then place the handset with
the battery compartment open and the keypad
facing down in a dry, warm place for at least
72
hours (not in a microwave, oven etc.).
4. Do not switch on the handset again until it is
completely dry.
When it has fully dried out, you will normally be
able to use it again.
Questions and answers
If you have any questions about using your phone,
visit us at
www.siemens.com/gigasetcustomer-
care at any time. The table below contains a list of
common problems and possible solutions.
AL140 AL145
In standby mode
– Handset in charging cradle
– Handset out of charging cradle
approx.
1.0 W
approx.
0.8 W
approx.
1.2 W
approx.
1.0 W
During a call approx.
1.0
W
approx.
1.2 W
DECT standard is supported
GAP standard is supported
Range up to 300 m outdoors
up to 50 m indoors
Base station power supply 230 V ~/50 Hz
Environmental conditions
in
operation
+5° C to +45 °C;
20% to 75% humidity
!
Problem Cause Solution
Nothing
appears in
the
display.
The handset is not
turned on.
Battery pack is
flat.
Press the end call key
a for approx. 5 sec-
onds or place the
handset in the base
station.
Charge/replace the
battery pack
(page 3).
No reaction
to key press.
The keypad lock is
activated.
Press the hash key
R
for approx. 2 sec-
onds (page 1).
No wireless
connection to
the base sta
-
tion, Base
flashes in
the
display.
The handset is
outside the range
of the base sta
-
tion.
The handset is not
registered.
The base station is
not turned on.
Cords not routed
correctly.
Move the handset
closer to the base
station.
Register the handset
(page 3).
Check the power con-
nector at the base sta-
tion (page 2).
Check cord routing
(page 2).
You cannot
hear a ringer/
dialling tone
from the fixed
network.
The phone cord
supplied has not
been used or has
been replaced by
a new cord with
the wrong jack
connections.
Please always use the
phone cord supplied
or ensure that the jack
connections are cor
-
rect when purchasing
from a retailer
(
page 2).
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
You have entered
the wrong system
PIN.
Reset the system PIN
to the default 0000.
To do this, unplug the
mains unit from the
mains socket
£Press and hold the
paging key
£Plug the mains
adapter in again
£Hold the paging
key down for at least
another 2 seconds
and then release.
The
reset procedure is
now carried out.
The
handsets are de-
registered. The calls
list is cleared.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Siemens-AL140-Duo

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens AL140 Duo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens AL140 Duo in de taal/talen: Engels als bijlage per email.

De handleiding is 0,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens AL140 Duo

Siemens AL140 Duo Gebruiksaanwijzing - Nederlands - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info