526706
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
3
INSTALLATION INSTRUCTIONS
For Safety Warnings & Operating Instructions of oven (R-2B34) refer to the Operation
Manual included inside the oven.
Refer to the Installation Diagrams on page 8.
1. The mains plug must be accessible after installation or the oven must be connected to an electric
circuit provided with an all-pole switch (contact gap no less than 3 mm) to disconnect the oven in
case of danger. A safety-device like a fuse in the installation may be used as a switch.
2. Remove the built-in kit mounting brackets from the package.
3. EBR-2610/EBR-2612 (500 mm cupboard) (Fig. 1, page 8)
Position the two oven runners (B) with the front hooked over the front edge of the shelf and pressed
against the right and left walls of the kitchen cabinet.
EBR-2620/EBR-2622 (600 mm cupboard) (Fig. 2, page 8)
Position the two oven runners (B) with the front hooked over the front edge of the shelf and using the
top mounting brackets (C) as spacers, press against the right and left walls of the kitchen cabinet.
Attach the oven runners with the four screws (E) as shown in Figs. 1 and 2 (page 8).
4. Attach the two top mounting brackets (C) to the ceiling of the kitchen cabinet with the two tabs
firmly pressed against the front face, as shown in Figs. 1 and 2 (page 8). Secure each bracket with
two screws (E).
5. Remove adhesive protection and attach the cushion (D) to the rear of the oven, as shown in Fig. 3
(page 8). FIT CLOSE TO, BUT DO NOT COVER THE AIR INLET HOLES (8) ON THE REAR OF THE
OVEN.
6. Place the oven (1) onto the oven runners (B). Locate the front feet (5) into the recess of the oven
runners (3) as shown in Fig. 5 (page 8).
7. Connect the oven to the power supply.
Caution: Make sure that the power supply cord (4) does not cross over the cushion (D) as shown in
Fig. 3 (page 8).
8. Place the built-in frame (A) over the oven (1) and engage the top mounting brackets (C) as shown in
Fig. 4 (page 8). (Note: the cutouts for the screws go to the bottom.)
Gently press the top of the frame down into the brackets, until the bottom of the frame engages
under the oven and the oven runners (B) as shown in Fig. 5 (page 8).
9. Fasten the frame with two screws (F) secured from the underside into the oven runners (B) as shown
in Fig. 5 inset (page 8).
NOTE: The R-2B34 is designed to be fitted and operated in a kitchen unit. Therefore it is not supplied
with a rear spacer. If for any reason, it is not operated built-in, ensure there is a minimum free
space above the oven of 15 cm and a minimum gap of 44 mm between the rear of the oven
and the adjacent wall, to provide air circulation.
GB
Diagram of oven position will be inserted here after completion of VDE testing.
As request in fax SEGCC-940 - the information for seperate sheet has been
inserted on this page.
R-2B34 B/I/K English 5/4/01 9:49 am Page 3
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp EBR-2622 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp EBR-2622 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info