651323
3
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
3
We are pleased that you have chosen one of our gun safes to protect your
firearms. You can be assured that your safe meets the California Department
of Justice standards for firearm safety. This manual will provide you with the
information you need to:
• unpack and set up your safe
• open the safe
• operate the lock
• take full advantage of your safe’s special features.
Remember to keep your combination a secret. Writing down a combination
and putting it in a desk drawer is like leaving your door key under the mat –
it invites entry.
Please retain this manual for your records. If you have any questions about
your gun safe, please visit our website at www.sentrysafe.com or call Sentry
Customer Service at 1-800-828-1438 or 1-585-381-4900. Customer Service
representatives are ready to assist you, 8 a.m. to 6 p.m., E.S.T., Monday - Friday.
Thank you for purchasing this SentrySafe gun safe product.
Please read this manual before using this product.
WARNING!
UNBOLTING YOUR GUN SAFE FROM THE SHIPPING PALLET
!
This is a two-person operation and should not be attempted without help. Before attempting to unbolt your new safe,
be certain someone is with you to help steady the safe while you work. Ensure the safe is standing upright on a flat, level surface. (Fig. A)
NOTE: Sentry Group is not responsible for any costs incurred for unit to be removed from pallet and installed in place.
1. Using a wrench or pliers, remove the nuts located under the X-cut in the carpet in the bottom of the
unit. (Fig. B)
NOTE: If the bolts turn when you begin to remove the nuts, reach between the slats of the
pallet and hold the bolts, by hand and/or with pliers, as you turn the nuts.
2. Once the nuts are removed, use a hammer to tap the bolts through the bottom of the safe.
3. Close door and put handle in locked position.
4. With your helper, slide safe to one edge of pallet. Tip the safe so that the edge moves to the floor.
(Fig. C)
5. Remove the pallet and stand the safe upright on the floor.
Unbolting your gun safe from the shipping pallet
Tools/equipment required
• Adjustable wrench, pliers, or 17 mm (11/16”) socket wrench
• Hammer
A
B
C
Bolt-down instructions
To help provide maximum security, SentrySafe strongly recommends this safe be
bolted down. (Hardware supplied)
1. Select a suitable and convenient location for your safe. Set the safe in place and
use the holes provided in the bottom or back of the safe to mark the location
of the holes to be drilled in the floor or wall. It is not recommended to attempt
to bolt to both floor and wall. If bolting to a wall, please ensure that the safe is
resting firmly on the floor.
Note: Fire-Safe models cannot be bolted to the wall.
2. Move the safe away and drill holes of the appropriate diameter and depth for the
type of hardware and the mounting surface being used (2 each – bolts, washers
and masonry anchors).
3. Place the safe back over the holes and install the fasteners as required. If a water
resistant unit was purchased, rubberized washers are provided. Assure that the
area around the safe hole opening is clean using a damp cloth. Place the rubber
side of the washer facing down against the safe floor and install the fastener.
NOTE: SentrySafe is not responsible for any costs incurred if unit is to
be replaced.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sentry EF3428E - Executive Fire-Safe bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sentry EF3428E - Executive Fire-Safe in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info