651329
2
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
1
Getting started
1
Installation of the batteries
(keep door open during setup):
1. Turn the keypad housing counter clockwise
and carefully pull away from the mounting
plate to expose battery compartment.
2. Install four new AAA Alkaline batteries
(factory installed batteries may be included
with some models).
Caution: Hold onto the
keypad housing to avoid pulling wires.
Note: Do not use rechargeable batteries or any
other type of non-alkaline battery. Do not mix
old and new batteries. Do not mix alkaline and
standard batteries.
3. Carefully position the keypad into the
inserts on the mounting plate and turn
clockwise. Ensure that there are no wires or
cables trapped between the keypad and the
mounting plate. Pinched cables result in a
short circuit.
4. Enter: * - Master or Manager Code (from
front of booklet) - #
The lock will indicate a valid code entry with
a single signal and the open light will stay
green for five (5) seconds.
5. Turn the handle clockwise before the green
light disappears.
Depository Safe
Thank you for purchasing this security safe from Sentry
®
Safe. This guide is designed to maximize the user and security features of this product.
The SentrySafe electronic lock is shipped with a
factory set master & manager code (see front of
booklet). You should set the lock to your own
unique master & manager code immediately.
Please keep your codes in a secure location.
You may also register your codes on our
website at www.sentrysafe.com.
A single signal (LED flashes and beeps once)
response from the lock indicates valid entry.
A double signal (LED flashes and beeps
twice) response from the lock indicates an
invalid entry.
• If three incorrect entries are entered in a
row, the keypad will shut down for a period
of five minutes. During this shut down period
you will not get a response from the keypad.
Changing the Master Code
(Code length: 1 to 10 digit code)
Always
perform this operation with the door open.
1. Enter: # - Existing Master Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: 1 - * - New Master Code - # - New
Master Code - #, before the orange light
disappears.
If a mistake is made during the change, wait
thirty (30) seconds and repeat steps 1 thru 3.
Test the new code several times before closing
the door: Enter: * - Code - #
• The lock will indicate a valid code change
with a single signal.
• The lock will indicate an invalid code change
with a double signal and the old code is still
valid.
Changing the Manager Code
(Code length: 1 to 10 digit code)
Always
perform this operation with the door open.
1. Enter: # - Master Code or Manager Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: 2 - * - New Manger Code - # - New
Manager Code - #, before the orange light
disappears.
If a mistake is made during the change, wait
thirty (30) seconds and repeat steps 1 thru 3.
Test the new code several times before closing
the door: Enter: * - Code - #
• The lock will indicate a valid code change
with a single signal.
• The lock will indicate an invalid code change
with a double signal and the old code is still
valid.
Activate user codes
(Code length: 1 to 10 digit code)
Always
perform this operation with the door open.
1. Enter: # - Master Code or Manager Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: User ID Number (3-7) - * - New User
Code - # - New User Code - #, before the
orange light disappears.
If a mistake is made during the activation, wait
thirty (30) seconds and repeat steps 1 thru 3.
• The lock will indicate a valid code entry with
a single signal.
• The lock will indicate an invalid code entry
with a double signal and the old code is still
valid.
Example: # - Master Code or Manger Code - #
- 5 - * - New User Code - # - New User Code -
#. This will activate User Five (5).
Changing the user code
Always perform this operation with the door
open
1. Enter: # - User Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: New User Code - # - New User Code -
#, before the orange light disappears.
If a mistake is made during the change, wait
thirty (30) seconds and repeat steps 1 thru 3.
Test the new code several times before closing
the door: Enter: * - Code - #
• The lock will indicate a valid code change
with a single signal.
• The lock will indicate an invalid code change
with a double signal and the old code is still
valid.
The Master and Manager can also change
the user codes by following the Activate user
codes” section steps 1 thru 3.
Deleting user codes
Always perform this operation with the door
open.
1. Enter: # - Master Code or Manager Code - #
2. The set light will stay orange for ten (10) seconds.
3. Enter: User ID Number (3-7) - * - # - #
Programming your lock codes
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sentry DH-074E - Depository Safe bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sentry DH-074E - Depository Safe in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info