760097
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
EN-2
Setup
1. Operate the machine on a fl at and stable surface.
2. Ensure there is enough clear space at the rear of the machine for the lamination to exit the
machine.
3. The SLA 201 operates with laminating pouches 150 (2x75) micron – 250 (2x125) micron thick
(Credit card size to A4 size)
Operating the laminator
The SLA 201 is operated by rocker switch, located at the right hand side of the appliance.
1. Plug the machines cable into a convenient 13 Amp domestic supply outlet.
2. Switch the machine on using the ON/OFF switch. The red power light will com on.
3. For COLD laminating, select the COLD setting, the Green ready light will come on straight away
and COLD laminating can begin, (please note you will need special Cold Laminating Pouches).
4. For HOT laminating, select the Hot setting, Hot laminating can begin when the Green “Ready
light comes on (Allow approx 35 minute heat up time).
If choosing COLD laminating after you have been Hot Laminating the machine must be allowed
to cool to room temperature again
5. Prepare the laminating pouch for inserting into the machine. See How to load a laminating pouch
below Do not use pouches thicker than 250 mic (2x125 mic per side)
6. When the machine has reached operating temperature, you may insert the pouch (sealed edge
rst) squarely into the machine until it engages with the rollers. Never insert a pouch open edge
rst into the machine.
7. The pouch will move through the machine and exit at the rear.
8. During the process the READY light may go out as heat is absorbed by the laminating pouch.
This is normal.
9. Turn the laminator to OFF after use.
10. Remove the plug from the power supply.
IMPORTANT !
Do not touch the top of the machine during use, as this gets very hot. The Intermittence
Operation on this machine is 30 mins On and 10 mins Off , but we recommend that you allow the
machine to cool down for at least 15 mins after 30 mins use. Do not place items on top of the
machine at any time.
Laminating capacity
The SLA 201 is a personal laminator designed for hot and cold lamination.
The minimum laminating thickness is 150 (2x75) microns and the maximum thickness is 250 (2x125)
microns.
How to load a laminating pouch
The laminating pouch is sealed along one side. Open the pouch and place the paper to be laminated
centrally inside the pouch as close to the sealed edge as possible. Ensure there is an equal border all
round the paper (eg: A4 paper should have a 3mm border). The sealed edge (not the open edges) is
placed into the entry slot to start the lamination process.
ABS Anti-Blocking System
If the pouch was not inserted straight or the document is jamming push the ABS switch towards left.
You can then take the laminating pouch and its content out of the machine.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SLA 201 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SLA 201 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info