758390
7
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
- 7 - 03/2020
Copyright © 2020, Fast ČR, a.s.
ECO mode Fast mode Default
settings
Spout light A8 No Yes Yes
Pre-brew function* Yes No Yes
Automatic shut-o time 10 minutes 30 minutes 20 minutes
Option to save amount of
espresso / hot water to memory
Yes Yes Yes / Reset to
default settings
*Note:
The pre-brew function means that the ground coee is rst moistened with asmall
amount of water. This will cause the coee to swell and thereby when it is subsequently
fully brewed, its avour will be developed fully, and its aromatic compounds and essential
oils will be fully extracted.
1. In the stand-by mode, press and hold down button B7 for 5 seconds. Button B7
will start ashing and at the same time other buttons will also be ashing or lit
depending on the mode that is set.
Button B8 Button B9 Button B10
ECO mode Lit Flashing Flashing
Fast mode Flashing Lit Flashing
Default settings Flashing Flashing Lit
2. To set the ECO mode, press button B8, to set the fast mode press button B9 and
to reset to default settings, press button B10. After setting amode, 2 beeps will
be made. In the event that you attempt to set amode that is already set, the
appliance will not react to the button being pressed.
3. If you do not wish to change the mode settings, press button B7 once more, or
wait 5 seconds until the appliance automatically switches back to the stand-by
mode.
CLEANING AND MAINTENANCE
Everyday cleaning and maintenance
Timely cleaning and maintenance is very important for operating the appliance
and extending its lifetime.
Before cleaning, turn off the appliance, disconnect it from the power socket and
allow it to cool down.
Remove the outer drip tray A11. Empty out all its contents over asink, and wash it
using clean water and then dry it thoroughly.
Slide out the inner drip tray A10 with the coffee grounds container A9. Empty out
the coffee grounds container A9 and wash it with clean water. Then dry it thoroughly.
Empty out the inner drip tray A10 and if dirty, wipe it with aclean dampened cloth
and then dry it thoroughly.
Install the inner drip tray A10, coffee grounds container A9 and the outer drip tray
A11 back in their place.
Slide out and remove the service access door A7. Press the brewing unit release
button and take out the brewing unit A6. Wash it under running water and dry
it out thoroughly.
Install the brewing unit A6 properly in its place and attach the service access door A7.
In the event that the appliance will not be used again on the same day, empty out
the contents of the water tank A1 and put it back in its place.
Once amonth, it is recommended to thoroughly clean out the water tank A1 using
asoft cloth and asolution of water and neutral kitchen detergent. Then thoroughly
rinse out the water tank A1 with clean water, dry it and put it back in its place.
Only clean the coffee bean hopper A3 with aclean, dry cloth or paper towel. Do
not clean it with water.
To clean the outer surface of the appliance, use aclean, lightly dampened cloth.
Then wipe everything so that it is thoroughly dry. Do not use solvents, steel wool,
abrasive cleaning agents, etc. to clean the appliance.
Do not submerge the appliance or its power cord in water and do not wash it
under running water.
Self-Clean function
When indicator B5 lights up during operation, it is necessary to start the Self-
Clean function.
The appliance will work best when the Self-Clean function is used regularly, at least
once per month, or more frequently based on the hardness of the water that is
used. This will extend its lifetime and improve power efficiency because limescale
deposits negatively affect electricity consumption.
Fill the water tank A1 all the way to the maximum water mark according to the
instructions contained in chapter Filling the water tank.
Add descaling agents specially intended for descaling espresso machine type
appliances into the water tank A1. These agents can normally be purchased in
specialised electrical appliance stores or in online stores. Follow the instructions
on the manufacturer’spackaging when dosing the purchased descaling agent.
Attention:
For descaling, do not use vinegar, etc. Otherwise, the appliance could be
damaged.
Under the spout A8, place acontainer with acapacity of at least 1.1l.
In the stand-by mode, simultaneously press and hold down buttons B7 and B9
for 5 seconds. Abeep is made and indicator B5 and touch button B9 will flash.
To start the self cleaning process, press button B9.
Note:
In the event that you wish to return to the stand-by mode at this stage, press button B7.
The progress of the self cleaning procedure is signalled by indicator B5. Take care
to prevent scalding by hot water or the escaping steam. Do not interrupt the
process in this phase.
Once the water in the water tank A1 is used up, indicator B1 and button B9 will start
flashing. Empty out the remaining contents of the water tank A1 and fill it up to the
maximum water mark with clean water. When the filled water tank A1 is inserted
back into the appliance, indicator B1 will turn off.
Empty out the contents of the container under the spout A8 and put it back in its
place. To complete the self cleaning process, press button B9.
When the self cleaning process is complete, the appliance will turn off automatically.
Manual cleaning (ushing the spout)
We recommend that you always clean the coffee spout when you have finished
using it. It is also recommended to do this when the appliance has not been used
for an extended period of time.
In the stand-by mode, simultaneously press and hold down buttons B7 and B8
for 5 seconds.
The light on buttons B8, B9 andB10 will turn off. Asmall amount of water will
flow out of the spout, which will flush it out. Water will flow into the drip tray A11.
Attention:
Avoid coming into contact with hot water.
After finishing the manual clean, the appliance will switch back to the stand-by
mode.
Drain internal lines
It is recommended to drain the internal lines when you plan on not using the
appliance for and extended period of time, before transporting it, etc.
In the stand-by mode, simultaneously press and hold down buttons B7 and B10
for 5 seconds. Indicator B6 will start flashing.
Remove the water tank A1 from the appliance. Indicator B6 will be lit. This signals
that the draining of the internal lines is running.
Note:
If you press button B7 before taking out the water tank A1, you will return back to
the stand-by mode.
When the internal line draining process is complete, the appliance will turn off
automatically.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SES 7015CH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SES 7015CH in de taal/talen: Engels als bijlage per email.

De handleiding is 0,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info