759223
7
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
- 7 - 08/2019
Copyright © 2019, Fast ČR, a.s.
EN Convection heater
User'smanual
Prior to using this appliance, please read the user’smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user’smanual in asafe place where it can be easily retrieved for future use.
We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Display
A2 Front panel
A3 Travel wheels
A4 Wall mounting hooks
A5 Main power switch (located on the
side)
A6 Wall mounting set (not shown)
DESCRIPTION OF THE CONTROL PANEL
B1 Button
B2 Button
B3 On/Off button
B4 Timer button
B5 Operating mode selection button
DESCRIPTION OF THE DISPLAY
C1 Child lock icon
C2 °C icon
C3 Timer icon
C4 Heating icon
C5 Temperature or timer display
C6 Anti-frost mode icon
C7 Low heating power mode icon
C7 High heating power mode icon
C9 WiFi icon
DESCRIPTION OF THE REMOTE CONTROL
D1 On/Off button
D2 Operating mode setting button
D3 Temperature setting button
D4 Timer setting button
D5 Plus (+) button
D6 Minus (-) button
BEFORE FIRST USE
Before first use, take the appliance and its accessories out of the packaging material
and remove all promotional labels and stickers. Check that neither the appliance nor
any of its parts is damaged.
INSTALLATION
The convection heater may be used as amobile heat source (necessary to install
the travel wheels A3) or it may be mounted on awall (travel wheels A3 must be
removed).
Warning:
Before any type of installation, always make sure that the power
plug is disconnected from the power socket.
Installing the travel wheels
Put ablanket or another soft underlay on the floor. Then place the convection heater
upside down on to this blanket.
On the underside of the convection heater there are three drilled holes on either
side. Align these holes with the holes in the travel wheels A3 and, using the supplied
self-tapping screws, screw them to the underside of the convection heater – see
figure E. Tighten securely. Check that the travel wheels A3 are correctly attached to
the convection heater.
Turn the convection heater over and carefully put it down on the travel wheels A3.
Check that the wheels move freely and that they are not blocked in any way.
Wall mounted installation
Before mounting the convection heater on awall, it is important that you check that
the installation location has no wires, conduits, pipes, etc. in the wall.
Prior to installation, also check that the installation location is at asufficient distance
from the power socket.
Warning:
Only use the supplied set of screws and dowels for the
installation. Under no condition should dowels and screws be
used that have adifferent diameter, different specifications and
which are not approved by the manufacturer as suitable for the
installation of this type of product.
Drill two holes of 8mm diameter 40mm deep into the wall as shown in figure F.
Insert aplastic dowel into each of the drilled holes. Using ascrewdriver, secure the
screws and leave their heads protruding out approximately 6mm.
Put the convection heater on to the wall by sliding the screw heads into the holes
on the hanging hooks A4.
Warning:
The convection heater must be installed at least 15cm above
the ground and 50cm from the ceiling. The convection heater
must always be installed horizontally. Any electrical installations
must be performed by a qualified electrician. The convection
heater must not be installed behind doors or in an outdoor
environment.
USING THE CONVECTION HEATER
Inserting batteries into the remote control
Remove the battery compartment cover located on the underside of the remote
control. Insert 2x type AAA 1.5Vbatteries (batteries not included) Ensure that the
correct polarity is adhered to as marked on the bottom of the battery compartment.
Put the cover back on.
When replacing batteries, proceed in the same manner. Always replace both
batteries at the same time. Avoid using acombination of new and old batteries or
batteries of various types.
If you wish to use the remote control, point it at approximately the level of the
display A1. The maximum signal range is 6m. If the remote control is positioned in
such away that obstacles prevent the transmission of the signal, then the signal may
not be transmitted at all.
Note:
When not using the remote control for an extended period of time,
remove the batteries from the remote control. Never put the batteries
in afire, short circuit them or damage them in any way. Dispose of them
ecologically at the end of their lifetime. Never throw batteries out with
communal waste.
Turning on / off
Prior to first use, check that the voltage in your power socket corresponds to the
voltage on the rating label.
Insert the power plug into apower socket.
Set the main switch A5 to position I(On). Asound is made, the display A1 is lit and
the temperature is shown.
To turn on the convection heater, press button B3 on the convection heater or
button D1 on the remote control.
The icon of the last set operating mode will be shown on the display A1.
When you have finished using it, press the On/Off button B3 on the convection
heater or button D1 on the remote control, and the convection heater will turn itself
off, however, it will remain in stand-by mode. To completely turn off the convection
heater, set the main switch A5 to position 0 (Off) and disconnect the power plug
from the power socket.
Note:
Upon first use or after it has not been used for an extended period of
time, aslight odour may be sensed or asmall amount of smoke may
be emitted from the convection heater. This is completely normal and
will quickly disappear.
Child safety lock
The child safety lock function enables the control panel to be locked and prevents
accidental changes to your settings.
To turn on the lock function, hold down button until the child safety lock icon C1
appears on the display A1. All the control buttons will be disabled.
To cancel the child safety lock function, hold down button until the child safety
lock icon C1 disappears from the display A1.
Selecting an operating mode
The convection heater has three operating modes: low heating power mode (input
750 W), high heating power mode (input 1500 W) and an Anti-Frost mode.
Press button B5 on the convection heater or button D2 on the remote control and
then use buttons / on the convection heater or the +/- buttons on the remote
control to select the required operating mode. The icon of the selected mode (C6, C7
or C8) will be lit on the display A1.
Note:
If also the heating icon C4 is lit on the display A1, this means that the
convection heater is running and is heating to the set temperature. As
soon as the set temperature is reached, the heating icon C4 will turn
off and only the icon of the selected operating mode will remain lit.
Setting the temperature
Press button B5 on the convection heater twice or button D3 on the remote control
once. The temperatures digits will start flashing. Set the temperature of the selected
mode using the / buttons on the convection heater or the +/- buttons on the
remote control. Your settings are saved when the temperature digits stop flashing.
You can set the temperature in the range from 5 to 50 °C.
Setting the timer
While the convection heater is running, press button B4 on the convection heater or
button D4 on the remote control. The timer icon C3 will be shown on the display A1
and the timer digits “00” will start flashing. Set the convection heater operating time
using the / buttons on the convection heater or the +/- buttons on the remote
control. Your settings are saved when the timer digits stop flashing. The timer icon
C3 will remain lit on the display A1. The set time in hours will start counting down
on the display A1. When the set time has elapsed, the convection heater will turn off
and switch to the stand-by mode.
The operating time can be set in the range from 1 to 24 hours.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Sencor-SCF-4201

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SCF 4201 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SCF 4201 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info