664156
10
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
ENGLISHENGLISH
BRAKE
Fork/Front Brake assembly:
Advisory: The SCOTT Plasma Fork is compatible with both SHIMANO direct
mount and single bolt front brake calipers. The recommended front brake
caliper for the SCOTT Plasma 5 is the TEKTRO SCTT161411501, especially
designed for the Plasma 5. Only this brake model is compatible with the front
aero brake cover (401) delivered with the SCOTT Plasma 5 frameset. Instructions
below describe the TEKTRO SCTT161411501 assembly.
Assemble the front brake axles on the fork and tighten to the specified torque (T5)
using an 8mm dynamometric wrench.
Position the spring on the axles, its final position is reached when the spring touches
the fork.
Position the brake caliper on the brake axles, the shouldering of the axles should
touch the caliper bearings then position the spring ends into the plastic spring tab
grooves using a small flathead screwdriver. Position the brake booster part at the end
of the brake axles so that the recesses are showing.
IMPORTANT
Make sure the front face of the brake booster part coincides with the front end
of the brake axles! Assemble the two M6 screws and tighten them to the specified
torque (T6).
Front Brake Cable assembly:
Install the front wheel in the fork tabs and position the front brake cable in front of
the front brake calliper. Using a pen put a mark on the cable corresponding to the
end of the cable anchor part.
Using a ruler and a pen, put a second mark on the cable 20mm below the first one
and cut the cable at the second mark.
Slide the cable into the cable anchor part; make sure the end of the brake cable does
not collide with the brake rod axle, in case you can gently bend the cable end so that
it goes aside from the brake rod axle part.
IMPORTANT
Gently pull the cable end using pliers. Position the brake pads so that they’re
approximately 1mm away from the braking surface. Make sure the cable clamps
parts are parallel and that the gap between these parts is perpendicular to the
cable clamping screw!
Tighten the cable clamping screw using a 2.5mm Allen key and a 3mm Allen key to
keep the cable anchor part from rotating. Adjust the pad position so that the top of
the pad is 1-2mm below the top of the rim’s braking surface and flat against the rim
surface.
Torque the brake pads bolts to 5Nm. Micro-adjust the brake pads position thanks
to the front brake stop part (305) located below the stem. Micro-adjust the spring
tension screws with a 2mm Allen key to center the brake pads relative to the rim.
19 |
BIKE USER MANUAL | PLASMA 5PLASMA 5 | BIKE USER MANUAL
| 18
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scott Plasma 5 - 2016 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scott Plasma 5 - 2016 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Scott Plasma 5 - 2016

Scott Plasma 5 - 2016 Gebruiksaanwijzing - Deutsch - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info