739111
5
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
19
If possible, install the device on the north- or east-
facing wall of the building.
If possible, install the device under roof overhangs
or similar covering.
If possible, the connection line should be inserted
into the device from below. If the connecting cable
enters into the device from above, particularly good
insulation must be ensured.
Install the load to be switched (lighting) in such a
way that the light from it does not fall on the light
sensor (Fig.!E). Otherwise, the sensor will not
be able to calculate the ambient brightness
correctly (optical feedback).
Tips on choosing the right installation site
V5448_581_01.book Seite 19 Mittwoch, 26. Oktober 2005 12:55 12
20
¼
Risk of fatal injury
from electrical current.
The light-sensitive time switch may only be
installed and connected by skilled electricians.
Please observe the relevant regulations in your
own country.
Installing the light-sensitive time switch and taking it
into service is done in several stages, and these must
be carried out as described below.
Installing the housing and wiring the connections
1Open the housing by unscrewing the two screws at
the front. Pull out the light-sensitive time switch.
The condensation water opening on the underside of
the housing must be opened. Exception: If operated in
How to mount the light-sensitive time
switch
V5448_581_01.book Seite 20 Mittwoch, 26. Oktober 2005 12:55 12
21
rooms subject to a large amount of dust, it must remain
closed.
2Push open the condensation water opening (Fig.
(A, view from rear) from the inside to the outside
and break out the device wall.
3Fasten the housing to the building wall through the
openings (Fig. !E and „E) using suitable fixing
material (e.g. dowels and screws). The "OBEN/TOP"
marking should be at the top.
If you want to lead the cable into the housing from
below rather than above:
4Swap over the lead-in guides (Fig. / A/B).
5Wiring the light-sensitive time switch for the desired
application:
–Figure %: Light-sensitive time switch A with load
B and On/Off switch C (optional).
V5448_581_01.book Seite 21 Mittwoch, 26. Oktober 2005 12:55 12
22
–Figure &: Light-sensitive time switch A with load
B, On/Off switch C (optional) and two-way
switch D for toggling between manual and
automatic operation.
6Insert the light-sensitive time switch into the
housing and screw the housing together.
Setting the twilight threshold
|Note: To set the twilight threshold, the device
housing must be open. Make sure that the light
sensor is not covered and that no light other than
the ambient brightness falls on the lights sensor.
1Turn the setting switch for switch-on time (Fig !C)
to position "T".
V5448_581_01.book Seite 22 Mittwoch, 26. Oktober 2005 12:55 12
23
On reaching the threshold value required:
2Slowly turn the setting switch for the twilight
threshold (Fig !A) until the light switches on.
Leave the setting switch at this position.
3Turn the setting switch for switch-on time (Fig !C)
to position "A".
Setting the twilight function
If you want to set the threshold function (switching on
and off at dusk/dawn, Fig. ):
1Turn the setting switch for switch-off time (Fig !B)
to position "D".
2Turn the setting switch for switch-on time (Fig !C)
to position "A".
V5448_581_01.book Seite 23 Mittwoch, 26. Oktober 2005 12:55 12
24
Setting the automatic function
If you want to set the automatic function (time switch
evening and morning, Fig. §):
1Read off the local time deviation from the table (see
next section) and calculate the switch-on or switch-
off time.
2Turn the setting switch for switch-off time (Fig !B)
to the newly calculated switch-off time, e. g. 21:30.
3Turn the setting switch for switch-on time (Fig !C)
to the newly calculated switch-on time, e. g. 5:15.
Semi-automatic function
If you want to set the semi-automatic function (time
switch evening only, Fig. $):
1Read off the local time deviation from the table (see
next section) and calculate the switch-on time.
V5448_581_01.book Seite 24 Mittwoch, 26. Oktober 2005 12:55 12
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Schneider-Electric-Merten-Argus-544890

Zoeken resetten

  • wanneer als de rookmelder om een paar minuten een bieptoon geeft? Gesteld op 24-6-2022 om 10:57

    Reageer op deze vraag Misbruik melden
  • Als de schemerschakelaar continue aan blijft kan dan het relais kapot zijn?Hoe kan ik dit controleren?Is het eenvoudiger om een nieuwe schakelaar te kopen en de defecte te vervangen? Gesteld op 3-12-2021 om 11:32

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Schneider Electric Merten Argus 544890 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Schneider Electric Merten Argus 544890 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 2,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info