612455
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
V5075-561-00 09/08
CONNECT radio receiver, flush-mounted, 1-gang switchArt. no. MTN507501© Merten2005V5075-561-0009/08
¼
DANGER
Risk of fatal injury due to electrical current
All work on the device should only be carried out
by trained and skilled electricians. Observe the
country-specific regulations.
½
CAUTION
If you operate devices that do not correspond to
the technical specifications (see technical data),
the connected devices and dimmers may get
damaged.
Connect only one phase (AC 230 V) towards
neutral conductor or functional extra-low volt-
age (FELV) to the make contact.
Do not connect the flush-mounted receiver to
different phases.
In the flush-mounted receiver, the make con-
tact is only separated from the phase by basic
insulation. You must therefore not connect any
safety extra-low voltage (SELV) (safety level
overridden).
The flush-mounted CONNECT radio receiver for the
switch will be referred to in the following as "the flush-
mounted receiver".
The flush-mounted receiver can be used to switch loads
on and off via radio (for information on allowed loads, see
the technical data). When it receives the radio signal, the
flush-mounted receiver switches the corresponding con-
tact.
|
The flush-mounted receiver cannot be used in a
wired two-way circuit.
CONNECT radio receiver, flush-
mounted, 1-gang switch
Operating instructions
Art. no. MTN507501
For your safety
Flush-mounted receiver introduction
en
¼
DANGER
Risk of fatal injury from electric current.
The device has no basic insulation and must
therefore be installed in a way that protects
against accidental contact.
¼
DANGER
Risk of fatal injury from electrical current.
Once a cover A is installed, the distance from
the fixing brackets or screws to the connections of
device B must be at least 4 mm.
If the distance is less than 4 mm, a deeper instal-
lation box must be used.
Also, the fixing brackets or screws of the cover
must not press against the housing.
½
CAUTION
The device can be damaged if not correctly
protected.
The circuit containing the connected loads must
be protected by a fuse with a rating not greater
than 16A.
Simply install the flush-mounted receiver "invisibly" near
the load to be connected, for example in a flush-mounted
socket with a blanking cover.
1 Connecting the flush-mounted receiver.
2 Installing the flush-mounted receiver.
Installing the flush-mounted receiver
B
> 4 mm
A
N
LN
L
10 A
|
Place the antenna as far as possible from metal
parts (connecting cables, retaining rings, etc.) to
avoid interruptions to the radio signal.
|
Metal surfaces in the immediate vicinity (e.g.
flush-mounted metal outlets, metal door frames)
can affect reception.
You can operate the flush-mounted receiver using the
following operating elements:
A taught CONNECT transmitter (e.g. CONNECT radio
push-button/CONNECT sensor surface).
Briefly press switch button B on the device
: this switches the channel.
Only insulated tools may be used for operation on the de-
vice, e.g. an insulated phase tester.
If the flush-mounted receiver is configured with EASY
CONNECT, not all functions/channels can be used. A
description of the EASY CONNECT radio system can be
found in the separate "CONNECT radio system" descrip-
tion, which is supplied with devices with system adminis-
tration (e.g. CONNECT radio push-button).
|
You can analyse and check faults throughout the
radio system with the help of the CONNECT radio
USB data interface (on a suitable PC) and the
CONNECT radio configuration tool.
The device does not react to the taught
transmitter:
Make sure that the maximum range is not exceeded
and that there are no metal surfaces such as metal
cabinets in the radio transmission path.
If necessary, check that the battery is placed correctly
in the radio push-button and that it is not flat.
Make sure that the device is not in programming
mode. (If the LED is flashing, this is the case.)
If necessary, repeat the teaching process.
Operating the flush-mounted receiver
A LED
B Switch button
What should I do if there is a problem?
A
B
NL**
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Schneider Electric MTN507501 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Schneider Electric MTN507501 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Schneider Electric MTN507501

Schneider Electric MTN507501 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info