782507
30
Verklein
Vergroot
Pagina terug
1/304
Pagina verder
30 GB/IE

Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
Swing the machine head (4) upwards and lock with
the locking bolt (23).
Loosen the retaining screw (5a) of the cover using a
Philips screwdriver.
WARNING! Do not fully remove this screw.
Fold the saw blade guard (5) upwards until the saw
blade guard (5) is above the ange screw (28).
With one hand insert the Allen key (C) in the ange
screw (29).
Hold the Allen key (C) and slowly close the saw
blade guard (5) until it touches the Allen key (C).
Firmly press the saw shaft lock (30) and slowly ro-
tate the ange screw (28) in clockwise direction.
The saw shaft lock (30) engages after no more than
one rotation.
Now, using a little more force, slacken the ange
screw (29) in the clockwise direction.
Turn the ange screw (28) right out and remove the
outer ange (29).
Take the blade (6) off the inner ange (31) and pull
out downwards.
Carefully clean the ange screw (28), outer ange
(29) and inner ange (32).
Fit and fasten the new saw blade (6) in reverse or-
der.
Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (6)
must coincide with the direction of the arrow on the
housing.
Before continuing your work make sure that all safe-
ty devices are in good working condition.
Important! Every time that you change the saw
blade (6), check to see that it spins freely in the ta-
ble insert (10) in both perpendicular and 45° angle
settings.
Important! The work to change and align the saw
blade (6) must be carried out correctly.

Press the ON/OFF switch laser (33) 1x. A laser line is
projected onto the material you wish to process, pro-
viding an exact guide for the cut. Press again the ON/
OFF switch (34) to toggle between the laser (32) and
the LED working light (33):
ON/OFF switch laser/LED (34)
Press 1x. Laser ON / LED OFF
Press 2x. Laser OFF / LED ON
Press 3x. Laser ON / LED ON
Press 4x. Laser OFF / LED OFF

If the laser (32) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (32b) and remove the front cover (32a). Loos-
en the Philips head screws (E) and set the laser by
moving sideways until the laser beam strikes the teeth
of the saw blade (6).
After adjusting and tightening the laser, mount the
front cover by tightening both screws (32b) by hand.
9. Transport
Tighten the handle (11) to lock the rotary table.
Press the machine head (4) downwards and secure
with the locking bolt (23).
Fix the saw’s drag function with the locking screw
for drag guide (20) in rear position.
Carry the equipment by the xed saw table (15).
When reassembling the equipment proceed as de-
scribed under section 7.
10. Maintenance
m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time us-
ing a cloth. In order to extend the service life of the tool, oil
the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
Cleaning the moving saw blade guard safety
device (5)
Always check the saw blade guard for debris before
using the machine.
Remove old sawdust and splinters using a brush or
similar tool.
Replacing the table insert
Danger!
With a damaged table insert (10) there is a risk of
small parts getting stuck between table insert and
saw blade, blocking the saw blade.
Immediately replace damaged table inserts!
1. Remove screws at table insert. If required, turn ro-
tary table and incline saw head to be able to reach
the screws.
2. Remove table insert.
3. Install new table insert.
4. Tighten the screws at table insert.
Brush inspection
Check the carbon brushes after the rst 50 operating
hours with a new machine, or when new brushes have
been tted. After carrying out the rst check, repeat
the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HM81LXU bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HM81LXU in de taal/talen: Alle talen als bijlage per email.

De handleiding is 10,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info