781964
22
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
www.scheppach.com / ser[email protected] / +(49)-08223-4002-99 / +(49)-08223-4002-58
22 | GB
10.1 Checking the oil level (17)
The hydraulic unit is a closed system with oil tank, oil
pump and control valve. Check the oil level regularly
before every use. Too low an oil level can damage the
oil pump. The correct oil level is approx. 10 to 20 mm
below the oil tank surface.
If the oil level is at the lower notch, then the oil level is
at a minimum. Should this be the case, oil must be im-
mediately added. The upper notch indicates the max-
imum oil level. The machine must be on level ground.
Screw in the oil dipstick fully, to measure the oil level.
10.2 Ventilation screw (16)
Before operating your machine, the bleed screw
should be loosened by some rotations until air can go
in and out of the oil tank smoothly. Failed to loosen the
bleed screw will keep the sealed air in hydraulic sys-
tem being compressed after being decompressed.
Such continuous compression/decompression will
blow out the seals of the hydraulic system and cause
permanent damage to your machine.
Before moving your machine, make sure the bleed
screw is tightened to avoid oil leaking from this point.
10.3 Splitting logs
Only split logs that have been sawn off straight. To do
this, proceed as follows:
1. Place the log plain onto the work table.
2. Your machine is equipped with Two-hands Con-
trol System that requires to be operated by both
hands of the user – left hand controls the control
lever (15) while right hand controls the push but-
ton switch (14).
3. Close the protective guard (3) so that the safety
switch is actuated.
4. Press the operating lever (15) downwards and in-
itiate the splitting process by pressing the release
button (14).
The log splitter will freeze upon absence of either
hand. If the protective guard (3) is opened during the
splitting process, the unit stops immediately.
Never force your machine for more than 5 seconds by
keeping pressure on it to split excessively hard wood.
After this time interval, the oil under pressure will be
overheated and the machine could be damaged. For
such extremely hard log, rotate it by 90° to see wheth-
er it can be split in a different direction. In any case,
if you are not able to split the log, this means that its
hardness exceeds the capacity of the machine and
thus should be discarded to protect the log splitter.
3. Connect the splitter to the stand (6) with 5 round
head screws with set of square and self-locking
nuts, the nuts must be installed on the outside.
9.3 Installing the protective guard (Fig. 9 - 14)
1. Attach the handle (2) and x it with two pan-head
screws with hexagon socket (M8 x 12mm) and
washers.
2. Now fasten the protective guard (1) between the
hand guard and the pressure stamp with two pan-
head screws with hexagon socket (M8 x 12mm).
Then x the protective guard to the hand guard
with a pan-head screw with hexagon socket (M8 x
16mm), a washer and a hexagon nut.
3. Now attach the protective guard (4). Place it in
the metal lugs to the left and right of the splitting
wedge. Fix the tting with four pan-head screws
with hexagon socket (M5 x 16mm), washers and
hexagon nuts.
4. Now install the last protective guard (3) Attach
the handle (2) and x it with two pan-head screws
with hexagon socket (M8 x 12mm) and washers.
Fasten the plain bearings to the lower side of the
protective guard (3) with two pan-head screws
with hexagon socket (M6 x 35mm), one washer
and one hexagon nut. Leave the screws loose for
the time being.
Make sure that the actuator of the safety
switch is installed on the correct side.
5. Now slide the protective guard (3) onto the sliding
shafts as shown in Fig. 14 and move it forward
until the actuator engages in the safety switch.
6. Now tighten all screws of the plain bearings.
9.4 Installing the tray table (5) (Fig. 15 + 16)
1. Attach the tray table to the protective panels and
secure with four pan-head screws with hexagon
socket (M6 x 16mm), washers and hexagon nuts.
m IMPORTANT!
You must fully assemble the appliance before using it
for the rst time!
10. Initial operation
Make sure the machine is completely and expertly as-
sembled. Check before every use:
the connection cables for any defective spots
(cracks, cuts etc.).
the machine for any possible damage.
the rm seat of all bolts.
the hydraulic system for leakage.
the oil level and
the safety devices
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HL455 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HL455 in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 5,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info