782176
29
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
29GB
wheels and can be moved. Hold the machine by its
frame (9).
Attention! Note the high centre of gravity of the ma-
chine.
Attention! Never use separating safety guards to lift
or transport the unit.
10. Working instructions
The following recommendations are examples of the
safe use of band saws. The following safe working
methods should be seen as an aid to safety. They can-
not be applied suitably completely or comprehensively
to every use. They cannot treat every possible danger-
ous condition and must be interpreted carefully.
Connect the machine to a suction unit when working
in closed rooms. A suction device which conforms
with commercial regulations must be used for suction
in commercial areas.
Loosen the sawband when the machine is not in op-
eration (e.g. after nishing work). Attach a notice on
the tension of the saw band to the machine for the next
user.
Collect unused sawbands and store them safely in a
dry place. Check for faults (teeth, cracks) before use.
Do not use faulty sawbands!
Wear suitable gloves when handling sawbands.
All protective and safety devices must be securely
mounted on the machine before beginning work.
Never clean the sawband or the sawband guide with a
hand-held brush or scraper while the sawband is run-
ning. Resin-covered sawbands impair working safety
and must be cleaned regularly.
For your own protection, wear protective glasses and
hearing protection. Wear a hairnet if you have long hair.
Roll up loose sleeves over the elbows.
Always position the sawband guide as near the work-
piece as possible when working.
Insure sufcient lighting in the work area and around
the machine.
Always use the fence for straight cuts to keep the work-
piece from tipping or slipping away.
When working on narrow workpieces with manual feed,
use the push stick.
For diagonal cuts, place the saw bench in the appro-
priate position and guide the workpiece on the fence.
Insure safe workpiece guidance.
For arced and irregular cuts, push the workpiece evenly
using both hands with the ngers together. Hold the
workpiece with your hands on a safe area.
Use a pattern for repeated arced or irregular cuts.
Insure that the workpiece does not roll when cutting
round pieces.
For safe work when transverse cutting, use the special
transverse cutting gauge accessory.
10.1 Performing longitudinal cuts (Fig. A)
Here, a workpiece is cut in its longitudinal direction.
Position the longitudinal fence (5) on the left side (if
possible) of the saw band, in accordance with the de-
sired width.
Lower the saw band guide (4) onto the workpiece. (8.9)
Switch on the saw.
Press one edge of the workpiece against the longitudi-
nal fence (5) with the right hand, whilst the at side lies
on the saw bench (7).
Slide the workpiece at an even feed rate along the lon-
gitudinal fence (5) into the saw band.
Important: Long workpieces must be secured against
tipping at the end of the cutting process (e.g. with reel-
off stand, etc.)
Attention! When processing narrower workpieces it is
essential to use a push stick.
The push stick (R) must always be stored within reach,
on the hook (j) provided for this purpose on the side of
the saw (Fig. 17).
10.2 Angled cuts (Fig. B+ Fig. 6)
In order to execute angled cuts parallel to the saw
band, it is possible to tilt the saw bench (7) for-
wards from 0° - 45°.
Release the locking handle (E).
Tilt saw bench (7) forwards, until the desired angle
is set on the degree scale (I).
Retighten the locking handle (E).
Attention: With a tilted saw bench (7), the longitudi-
nal fence (5) must be positioned on the downward
facing side to the right of the saw band in the work-
ing direction (if the workpiece width allows this),
in order to secure the workpiece against slipping.
Perform the cut as described under 10.1.
10.3 Freehand cuts (Fig. C)
One of the most important features of a band saw is
the ease with which it can cut curves and radii.
Lower the saw band guide (4) onto the workpiece. (8.9)
Switch on the saw.
Press the workpiece rmly onto the saw bench (7)
and slowly slide into the saw band.
During freehand cutting you should always work
with a low advancing speed, so that the saw band
can follow the desired line.
In many cases it is helpful to roughly saw curves
and corners approximately 6 mm from the line.
If it is necessary to saw curves that are too tight
for the saw band used, auxiliary cuts must be sawn
up to the front face of the curve, so that these fall
off as wood waste when the nal radius is sawn.
10.4 Executing cuts with the transverse cutting
gauge (Fig. D + Fig. 18) (optional)
Set transverse cutting gauge (14) to the desired
angle (see 8.10)
Perform the cut as described under 10.1.
11. Cleaning and maintenance
Important.
Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HBS250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HBS250 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 4,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info