782163
25
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
25GB
6. Technical data
Electro motor 230 - 240 V ~ ,50 Hz
Power S1 250W, S2 30 min 350W
Revolutions 1400 min-1
Saw band length 1400 mm
Saw band width 7 mm
Saw band width max. 12 mm
Cutting speed 880 m/min
Passage height 0 - 80 mm
Passage width 200 mm
Table size 300 x 300 mm
Slewing range of the
table 0° bis 45°
Max. size of the
workpiece 400 x 400 x 80 mm
Overall weight 16,5 kg
Subject to technical modications!
* Operating mode S1, continous operation.
The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
Noise parameters
The total noise values determined in accordance
with EN 61029.
sound pressure level LpA 77,4 dB(A)
uncertainty KpA 3 dB
sound power level LWA 90,4 dB(A)
uncertainty KWA 3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
7. Remaining hazards
The machine has been built using modern technolo-
gy in accordance with recognized safety rules. Some
remaining hazards, however, may still exist.
Risk of injury for ngers and hands by the rotating
saw band due to improper handling of the work
piece.
Risk of injury through the hurling work piece due
to improper handling, such as working without the
push stick.
Risk of damaging your health due to wood dust and
wood chips. Wear personal protective cloth such
as goggles. Use a tting dust extractor.
Risk of injury due to defective saw band. Regu-
larely check saw band for such defects.
Risk of injury for ngers and hands while changing
saw band. Wear proper gloves.
Risk of injury due to starting saw band while
switching on the machine.
The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
Wear only closetting clothes. Remove rings,
bracelets and other jewelry.
For the safety of long hair, wear a cap or hair net.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
Remaining hazards can be minimized by follow-
ing the instructions inGeneral safety instructions“
Proper Use“ and in the entire operating manual.
8. Attachment and operation
Before starting the equipment
Make sure the machine stands securely, i.e. bolt it
to a workbench or solid base. There are two holes
for this purpose in the machine foot. • The saw table
must be mounted correctly.
All covers and safety devices have to be properly
tted before the machine is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly tted and that the
machine’s moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Assembly tools
1 engineer’s wrench SW 10/13
1 hexagonal head spanner SW 3
1 hexagonal head spanner SW 4
Tabletop and the mounting angles are not mounted
for reasons of packaging technology.
8.1 Assembly of the table top (Fig.
1+2+3+4+5+5.1.5.2)
1 Remove the wing nut (E), the clamping lever (F),
the two disks and the plate (H). (Fig. 5.1)
2 Remove the 2 knurled nuts (D) and remove the U
bracing (C) from the working table. (Fig. 4)
3 Position the working table (A) over the rear (B)
to the screws. Fasten the working table with the
plate (H), the two disks, the wing nut (E) and
the clamping lever (F) to the machine housing.
Fig. 5.2)
4 Attach the U bracing (C) with 2 countersink screws
M6x16 and knurled nuts (D) at the front of the saw-
ing table. (Fig.3+4)
8.2 Adjusting the table top (Fig. 6)
1 Set the table top to home position and tighten the
wing bolt (E) and the clamp lever (F) rmly.
2 Align the table top parallel to the sawing blade
and tighten the 3 screws. Observe that the sawing
blade is centred in the table inlay.
8.3 Adjusting the table top at the right angle to
the sawing blade(Fig. 5+6)
1 Fully set the belt guide (4) upwards and clamp it
tight.
2 Release the clamping lever (F) and the wing bolt
(E) at the swivelling segment (G).
3 Align the table at the right angle (90°) to the sawing
blade (use back square).
4 Adjust the adjusting screw (I) and lock it with a
nut (J).
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HBS20 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HBS20 in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 5,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info