www.scheppach.com / ser[email protected] / +(49)-08223-4002-99 / +(49)-08223-4002-5846 | GB
Keep the noise emissions and vibrations to a
minimum.
Wear hearing protection.
The effects of noise can cause hearing damage.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Measured sound pressure level LpA 99 dB(A)
Uncertainty KpA 3 dB
Guaranteed sound power level LwA 114 dB(A)
Measured sound power level LwA 109.9 dB(A)
Uncertainty KwA 3 dB
Vibration Front handle 7.5 m/s²
Vibration Rear handle 7.0 m/s²
Uncertainty 1.5 m/s²
7. Before starting up
m CAUTION!: Start the engine only when the saw is
fully assembled and checked.
m ATTENTION!: Always wear high-strength
gloves when handling the saw chain or adjust-
ing it.
Assembling the bar, and the chain (Fig. 3-6)
Open the packaging and assemble the bar and chain
as follows:
1. Press the front hand guard back (Fig. 14/Pos. 3a)
so that the chain brake is disabled.
2. Loosen the two nuts (B) and remove the cover
(17) and spacer (A).
3. Mounting the stopper claw (Fig. 11)
Insert the stopper claw (19) into the recesses of
the housing (see Fig. 11) and secure with the 2
xing screws (A). Use the tool supplied with the
assembly tools (10).
4. Mount the bar on the two threaded pins (Fig. 4)
5. Slide the chain around the sprocket, next slide
the saw chain around the bar. Pay attention to the
installation direction of the chain. (Fig. 4-5)
6. Insert the chain tensioning screw (Z) into the low-
er hole of the chain bar (Y). (Fig. 4)
7. Install the cover (17) and tighten the nuts (B) by
hand.
Behaviour during an emergency
Start First Aid measures relevant to the injury and re-
quest medical help as quickly as possible. Prevent
the injured person from further injury and keep him/
her rested. For potentially occurring accidents, the
First Aid kit, according to DIN 13164, should always
be handy at the work place. Material taken from the
First Aid kit must be replaced immediately. When you
are requesting help, give the following information:
1. Location of accident
2. Type of accident
3. Number of injured people
4. Type of injuries
Store all safety notices and instructions for the
future.
6. Technical data
Machine without guide bar
L x W x H 430 x 255 x 250 mm
Weight without guide bar
and saw chain and empty
tank
5.5 kg
Weight with guide bar and
saw chain and empty tank 6.0 kg
Cutting Length 430 mm
Guide bar length 457 mm
Automatic chain oiling yes
Saw chain Oil Special saw chain Oil
Saw chain oil tank capac-
ity 0.26l
Saw chain division 3/8″
Drive link thickness 1.27 mm
Saw chain type Oregon 91PX062X
Number of teeths drive
sprocket 7
Tooth pitch of drive
sprocket 3/8″
Chain brake yes
Guide bar type Oregon
180SDEA095
Saw chain speed max. 22 m/s
Motor 1 cylinder 2 stroke
air-cooled
Engine capacity 46 cm³
Maximum motor capacity 2.0 kW
Idle speed 3300±200 min-1
Maximum speed with cut-
ting attachment 11000 min-1
Fuel tank capacity 0.55 l
Fuel type Mix 40:1
