22 GB
• Mark holes on board where belt/disc sander is to
be mounted using holes in the base as a template
for hole pattern.
• Follow last three steps in section Mounting Belt/
Disc Sander to Workbench.
If lag bolts are used, make sure they are long enough
to go through holes in belt/disc sander base and mate-
rial the belt/ disc sander is being mounted to. If ma-
chine bolts are used, make sure bolts are long enough
to go through holes in belt/disc sander, the material
being mounted to, and the lock washers and hex nuts.
8.6 On/Off switch (12)
• The grinder/sander can be switched on by press-
ing the green button „1“.
• To switch off the grinder/sander you must press
the red button „0“.
Warning: Do not reach across the sanding disc to
turn the belt/disc sander ON or OFF. Contact with the
sanding disc can result in serious personal injury.
8.7 Grinding/sanding
• Always hold the workpiece rmly during grinding/
sanding.
• Do not exert excessive pressure.
• To prevent the abrasive paper from becoming worn
on one side, the workpiece should be moved to
and from on the grindinög/sanding belt or grinding/
sanding plate as you grind/sand.
• Important! Pieces of wood should always be sand-
ed with the grain to prevent them splitting. Impor-
tant. If the grinding wheel or the grinding/sanding
belt becomes jammed during operation, please re-
move the workpiece until the tool reaches its top
speed again.
9. Transport
If you want to move the equipment to a different place,
disconnect the equipment from the power supply and
set it up in the new position you want to use it in.
10. Working instructions
Bevel sanding, Fig. 14
The worktable can be tilted from 0° to 45° for bevel
sanding. To tilt the worktable:
• Loosen the xing screw (1).
• Set worktable to desired angle. Note: Position the
worktable not further than 1/16 in. (1.6 mm) from
the sanding surface.
• Retighten the xing screw (1) again.
Sanding small end surfaces using the miter
gauge, Fig. 15
A miter gauge (13) is included with your tool for in-
creased accuracy. Use of a miter gauge is recom-
mended for sanding small end surfaces on the
sanding disc.
Note: Always move the workpiece across the sand-
ing disc from the left side towards the right side.
Horizontal and vertical sanding, Fig 10-12+16
Your belt/disc sander can sand both vertically and
horizontally. Depending on the workpiece, the work
support can be used with either the horizontal or ver-
tical sanding operation.
• Loosen the Allen screw (5)
• Move the grinding/sanding belt (6) upwards into
the desired position.
• Tighten the Allen screw (5) again to x this posi-
tion.
• In this position you can use the grinding/ sanding ta-
ble to support the workpiece. To do this, rst loosen
the two Allen screws (17) and then remove the stop
rail (7). The grinding table can now be pushed into the
hole in the holder tube (20) and xed with the screw (1)
Note: Sand long workpieces with the sanding belt
in the vertical position by moving the work evenly
across the sanding belt.
Surface sanding on the sanding belt, Fig. 17
• Hold the workpiece rmly, keeping ngers away
from the sanding belt.
• Keep the end pressed rmly against the work sup-
port (7) moving work evenly across the sanding
belt.
Note: Use extra caution when sanding very thin piec-
es and when sanding extra long pieces, remove the
work support (7). Apply only enough pressure to al-
low the sanding belt to remove the material.
Sanding curved pieces, see Fig. 18
Warning: Never attempt to sand the end pieces of a
workpiece on the idler drum. Applying the end of the
workpiece on the idler drum could cause the work-
piece to y up. Failure to heed this warning could re-
sult in serious personal injury.
Always sand inside curves on the idler drum as
shown in Figure 18.
• Hold the workpiece rmly, keeping ngers away
from the sanding belt.
• Keep the curve pressed rmly against the idler
drum moving work evenly across the sanding belt.
Note: Use extra caution when sanding very thin piec-
es and apply only enough pressure to allow the sand-
ing belt to remove the material.
Sanding outside curves on sanding disc Fig. 19
Always sand outside curves using the sanding disc
and moving the workpiece (W) from the left side of
center as shown in Figure 19
• Hold the workpiece rmly, keeping ngers away
from the sanding disc.
• Keep the curve pressed rmly against the sand-
ing disc moving work evenly on the left side of the
sanding disc.
Warning: Applying the workpiece to the right side
of the sanding disc could cause the workpiece kick-
back. Failure to heed this warning could result in seri-
ous personal injury.
