781478
17
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
17
Le courant présente un risque en cas d’utilisation de
lignes de branchement électrique non conformes.
Des risques résiduels non apparents sont toutefois en-
core possibles malgré toutes les mesures prises.
Il est possible de réduire les risques résiduels en respec-
tant les consignes de sécurité et lutilisation conforme
ainsi que les instructions de service.
Déballage de la machine
Fig. 2
Vérifier le contenu pour d’éventuels dommages de trans-
port.
En cas de dommage, ce dernier doit immédiatement être
signalé au transporteur. Vérifier si le contenu est au com-
plet.
Signaler immédiatement les pièces manquantes au
concessionnaire.
La machine est expédiée au complet dans un carton.
Les pièces complémentaires à fixer sur la machine doivent
être situées et affectées avant le montage.
1 Ponceuse à bande et à ponceuse à disque
2 1 table de ponceuse à bande
2 a 1 levier de serrage M 8 pour table de ponceuse à
bande
2 b 1 disque 8 mm pour table de ponceuse à bande
3 1 table de ponceuse à disque
3a 2 vis de blocage M6 pour table de ponceuse à
disque
3b 2 rondelles 6 mm pour table de ponceuse à disque
4 1 raccord d’aspiration
4a 3 vis à fente cruciforme M4 x 10 pour raccord
d’aspiration
4b 3 disques 4 mm
5 1 gabarit de découpe transversale pour table de
ponceuse à disque
6 2 clés à six pans SW 3 mm
Mode d’emploi
Montage
ATTENTION ! Sassurer que la machine nest pas connectée
au réseau électrique.
Montage de la table de ponceuse à bande. Fig. 3
Glisser la table de la ponceuse à bande (2 Fig. 2) sur la
bande de ponçage et la fixer sous la table à l’aide du levier
de serrage et le disque (2a et 2b Fig. 2) Le levier de ser-
rage est prétendu à l’aide d’un ressort et peut être réglé
par une traction sur la poignée.
Attention ! Pour éviter l’écrasement des doigts entre le
bande et la table, il convient de respecter une distance
minimale de 2 mm entre la table et le bande de ponçage.
Montage de la table de la ponceuse à disque, Fig. 4
Glisser la table de la ponceuse à disque (3 Fig. 1) avec les
épaulements dans l’évidement sur la machine et pousser
la table vers le haut jusqu’à ce que les perçages corres-
pondent et la fixer des deux côtés avec les vis de blocage
et les rondelles (3a et 3b Fig. 1).
Although having regarded all considerable rules there
may still remain not obvious remaining hazrds.
• Minimize remaining hazards by following the instruc-
tions in ”Safety Rules”, ”Use only as authorized” and in
the entire operating manual.
Unpacking the Machine
Fig. 2
Check the delivery for possible transport damage.
In case of damage, the carrier has to be notified immedi-
ately. Check the delivery is complete.
Inform the retailer immediately if there are any parts miss-
ing.
The machine is shipped complete in a cardboard box.
Additional parts for attachment to the machine have to be
located and accessed prior to mounting.
1 Belt and Disc Sander
2 1 band grinding table
2 a 1 locking lever M 8 for band grinding table
2 b 1 washer 8 mm for band grinding table
3 1 plate grinding table
3a 2 locking screws M6 for plate grinding table
3b 2 flat washers 6 mm for plate grinding table
4 1 vacuum connector
4a 3 crosshead screws M4 x 10 for vacuum connector
4b 3 washers 4 mm
5 1 transverse cutting template for plate grinding
table
6 2 hexagonal spanners SW 3 mm
Operating manual
Assembly
ATTENTION! Ensure that the machine is disconnected from
the mains supply.
Assembly of the grinding belt table. Fig.3
Slide the grinding belt table (2 Fig.2) on, above the grind-
ing belt, and fasten it under the table with the locking
lever and the washer (2a and 2b Fig.2).
The locking lever is pre-tensioned by a spring and can be
adjusted by pulling the grip.
ATTENTION!! To prevent fingers from being squeezed
between the band and table a minimum separation of 2
mm has to be maintained between the table and grinding
band.
Assembly the plate-grinding table Fig. 4
Slide the plate-grinding table (3 Fig.1) so the lugs fit into
the notch on the machine and press the table up until the
drilled holes match, and secure it with the locking screws
and washers (3a and 3b Fig.1) on both sides.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach BTS700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach BTS700 in de taal/talen: Nederlands, Duits, Engels, Frans, Fins als bijlage per email.

De handleiding is 3,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info