644555
10
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
12english
ingknobclockwise1/4turn.
• Ifthesandingbeltmovesawayfromthedisc,turnthe
trackingknobcounterclockwise1/4turn.
• Turn theswitch ON and then immediately OFF again,
notingbeltmovement.Readjusttrackingknobifneces-
sary.
Squaring the worktable to the sanding disc, Fig. 12
• Unplugthebelt/discsander.
• Using a combination square, check the angle of the
worktable with the sanding belt.
• Iftheworktableisnot90°withthedisc,loosenthetable
lock knob and tilt the table.
• Adjustworktablesquaretothesandingdiscandretight-
en the table lock knob.
Note:Usetheadjustmentscrewbeneaththeworktableto
move the table further or closer to the sanding disc.
WARNING: Beforeattemptingtouseyourbelt/discsander
familiarize yourself with all operating features and safety
requirements.
Locking the switch, Fig. 13
• PlacetheswitchintheOFFposition.
• Wait until the belt/discsanderhascometoa full and
complete stop.
WARNING: Do not reach across the sanding disc to turn the
belt/discsanderONorOFF.Contactwiththesandingdisc
can result in serious personal injury. See Figure 13.
m Hints for work
Bevel sanding, Fig. 14
The worktable can be tilted from 0° to 45° for bevel sand-
ing. To tilt the worktable:
• Loosenthetablelockknobbyturningitcounterclock-
wise.
• Setworktabletodesiredangle.
Note: Positiontheworktablenotfurtherthan1/16in.(1.6
mm) from the sanding surface.
• Tightenthetablelockknobbyturningitclockwise.
Sanding small end surfaces using the miter gauge, Fig. 15
A miter gauge is included with your tool for increased ac-
curacy.Useofamitergaugeisrecommendedforsanding
small end surfaces on the sanding disc.
Note:Alwaysmovetheworkpieceacrossthesandingdisc
from the left side towards the right side.
Horizontal and vertical sanding, Fig. 16
Your belt/disc sander can sand both vertically and hori-
zontally. Depending on the workpiece, the work support
can be used with either the horizontal or vertical sanding
operation.
• Insertthehexkeyprovidedintotheholesinthepulley
cover. Loosen the screws by turning them counterclock-
wise.
• Movethesandingbeltintoaverticalpositionasshown
inFigure16.Verticalpositioncanbechangedusingthe
vertical set screw.
• Lockthesandingbeltbyretighteningthescrews.Note:
Sand long workpieces with the sanding belt in the verti-
cal position by moving the work evenly across the sand-
ing belt.
Surface sanding on the sanding belt, Fig. 17
• Holdtheworkpiecermly,keepingngersawayfromthe
sanding belt.
• Keep theend pressed rmly against the work support
moving work evenly across the sanding belt.
Note: Useextracautionwhensandingverythinpiecesand
when sanding extra long pieces, remove the work support.
Apply only enough pressure to allow the sanding belt to
remove the material.
Sanding curved pieces, see Fig. 18 and 19
WARNING: Neverattempttosandtheendpiecesofawork-
piece on the idler drum. Applying the end of the workpiece
on the idler drum could cause the workpiece to y up.
Failure to heed this warning could result in serious per-
sonal injury.
Sanding inside curves on sanding belt:
Always sand inside curves on the idler drum as shown in
Figure 18.
• Holdtheworkpiecermly,keepingngersawayfromthe
sanding belt.
• Keep the curve pressed rmly against the idler drum
moving work evenly across the sanding belt.
Note: Useextracautionwhensandingverythinpiecesand
apply only enough pressure to allow the sanding belt to
remove the material.
WARNING: Applying the workpiece to the right side of the
sanding disc could cause the workpiece kickback. Failure
to heed this warning could result in serious personal in-
jury.
Sanding outside curves on sanding disc:
Always sand outside curves using the sanding disc and
moving the workpiece from the left side of center as shown
in Figure 19.
• Holdtheworkpiecermly,keepingngersawayfromthe
sanding disc.
• Keepthecurvepressedrmlyagainstthesandingdisc
moving work evenly on the left side of the sanding disc.
m Electrical connection
The installed electric motor is factory connected ready for
operation.TheconnectionmeetstheapplicableVDEand
DlNregulations.
The connection made by the customer as well as any ex-
tension cables used must comply with all relevant regula-
tions.
Connectionandrepairworkontheelctricequipmentmust
be carried out by a qualified technician only.
Important note
The motor rating is S 1. This means that when overloaded
it switches off automatically. After a cooling period (can
vary) you may switch it on again.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach BD9000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach BD9000 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info