699462
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
2 VERSA-LCDM-WRL SATEL
2. Description
Operating modes
The keypad can work in two modes:
active mode – started by pressing any key. Additionally, the active mode can be started automatically
when an alarm occurs or an entry delay, an exit delay or an auto-arming delay begins (see
description of the
W
AKE
-
UP
parameter, section “Settings stored in ABAX system controller” p. 5).
In this mode, the keypad operates in much the same way as the LCD wired keypad. The display is
ON and the backlight, LED signaling and sound signaling are active.
inactive mode – is started:
after 20 seconds since the last key press,
after preset time, if the active mode was started automatically (see description of the
W
AKE
-
UP
parameter, section “Settings stored in ABAX system controller” p. 5).
The purpose of the
inactive mode is to save energy. The display is off. Backlight, LED indication
and sound signaling are disabled (if a time different from 0 is preset for the
W
AKE
-
UP
parameter,
CHIME from zones will be signaled).
Support for proximity cards
The built-in
proximity card reader enables the system to be operated by using proximity cards (any
125 kHz passive transponder in the form of a card, tag, etc.). If the alarm system is not to be operated
by using the proximity cards, the reader can be disabled (thus reducing the battery consumption).
Periodic transmissions
Every 15 minutes, the
keypad sends a periodic transmission. The purpose of such transmissions is to
monitor presence and condition of the keypad.
Battery status control
The keypad controls the
status of the batteries. If the voltage is lower than 2.75 V:
low battery information is sent during each periodic transmission,
on entering the active mode, a low battery message will be displayed (the message will specify
which battery is to be replaced – the battery designation can be found on the electronics board,
after opening the enclosure).
The battery life depends on how the keypad is used. The more frequently the active mode is
entered, the quicker the batteries will be depleted.
3. Installation
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the batteries. The
manufacturer is not liable for the consequences of incorrect installation of the battery.
The used batteries must not be discarded, but should be disposed of in accordance
with the existing rules for environment protection.
The keypad is designed for indoor installation. The place of installation should be readily accessible to
the system users. When selecting the installation location, take into account the communication range
of the ABAX system.
1. Open the keypad enclosure (Fig. 2).
2
. Install the batteries and add the keypad to the wireless system (see: Adding the keypad to the
wireless sy
stem”).
3.
Put the cover on the catches and snap the enclosure shut.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel VERSA-LCDM-WRL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel VERSA-LCDM-WRL in de taal/talen: Engels als bijlage per email.

De handleiding is 0,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel VERSA-LCDM-WRL

Satel VERSA-LCDM-WRL Gebruiksaanwijzing - Nederlands - 12 pagina's

Satel VERSA-LCDM-WRL Gebruiksaanwijzing - Deutsch - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info