699902
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
SATEL RE-1K • RE-2K 3
The controller should be installed indoors, in spaces with normal air humidity. When selecting
the installation place, take into consideration that thick walls, metal partitions, etc. will reduce
the radio signal range. It is recommended that the controller be mounted high above the floor.
This will allow you to get a better range of radio communication and avoid the risk of the
controller being accidentally covered by people moving around the premises. Mounting the
controller near electrical installations is not advisable, as this may cause malfunction of the
device.
Note: When closing the enclosure, make sure that the programming button is not pressed by
the cables.
5. Configuring
You can configure the controller using PROGRAM button and K1 and K2 pins.
5.1 Enrolling a keyfob
1. Press the PROGRAM button. The LED will start flashing green.
2. Press the keyfob button. The LED will start flashing red.
Note: If the LED will turn on in green, it means that no more keyfobs can be enrolled or the
keyfob is not supported.
3. Press the same keyfob button again. The LED will turn on in green.
5.2 Restoring factory default settings and deleting keyfobs
When restoring the factory default settings, you can delete all keyfobs.
1. Press and hold down the PROGRAM button.
2. After about 7 seconds, when the LED starts flashing red, release the button.
3. When the LED stops flashing red and turns on in green, it means that the factory default
settings of the controller have been restored.
5.3 Setting the operating mode for a relay output
You can set a different operating mode for each relay output. The output 1 pins are used as
an example in the table below.
Pulse mode [jumper set on the two lower pins] – the relay output is turned on when
the keyfob button is pressed (up to 30 seconds – then the keyfob stops transmitting
to prevent the battery discharge).
Monostable mode [jumper set on the two upper pins] – pressing the keyfob button
turns on the relay output for a preset time.
Bistable mode [jumper removed from pins] – each pressing the keyfob button
changes the relay output status to the opposite one.
5.4 Programming the relay output cut-off time
If the relay output works in the monostable mode, you can program the cut-off time for it
ranging from 1 to approx. 250 seconds (by default: 5 seconds).
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel RE-2K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel RE-2K in de taal/talen: Engels als bijlage per email.

De handleiding is 0,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel RE-2K

Satel RE-2K Gebruiksaanwijzing - Nederlands - 4 pagina's

Satel RE-2K Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info