699892
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
2 MKP-300 SATEL
- disarm the system (or it’s a keypad with factory settings which has not been used for arming /
disarming).
The LED will remain lit for 15 seconds after pressing the key.
When performing operations on the keypad, the LEDs are used for communication with the user.
2.2 Sound signaling
When performing operations on the keypad, the following sounds are generated:
1 short beep – pressing any numeric key.
2 short beeps – starting function or correct code confirmation.
3 short beeps – command sent confirmation:
arming;
disarming and alarm clearing.
4 short and 1 long beep – command sent confirmation:
output control;
triggering fire or auxiliary (medical) alarm.
2 long beeps – unknown code or function not available.
3. Installation
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the battery. The
manufacturer is not liable for the consequences of incorrect installation of the battery.
The used batteries must not be discarded, but should be disposed of in accordance
with the existing rules for environment protection.
1. Open the enclosure.
2. Install the battery and register the keypad in the MICRA alarm module (see the manual for MICRA
alarm module).
3. Close the enclosure.
4. Select the place of installation. Check that the transmissions from the keypad placed at that point
reach the MICRA alarm module. In order to send a transmission, close and open the tamper
contact. If the alarm transmission is received, continue with the installation. If the alarm
transmission is not received, select a different mounting location and repeat the test.
5. Open the enclosure.
6. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the wall.
7. Close the enclosure.
4. Codes
The MICRA system can be operated from the keypad after entering the code (only a few functions
can be run without entering the code). The code consists of four digits. Pre-programmed by default in
the keypad is the administrator code: 1234.
Notes:
The factory code should be changed as soon as possible.
The administrator code can not be deleted.
The MICRA module can be preprogrammed by the installer so that entering an invalid code three
times will trigger an alarm.
The administrator code makes it possible to assign individual codes to the people who are to use the
security system. For security reasons, different people should not use the same code.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel MKP-300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel MKP-300 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel MKP-300

Satel MKP-300 Gebruiksaanwijzing - Nederlands - 4 pagina's

Satel MKP-300 Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info